Sterling 882.00722.00 manual Typical Surge Hopper Assembly Parts List

Page 49

Figure 57: Typical Surge Hopper Assembly Parts List

#	DESCRIPTION	010	020		040
1	Lid (Smaller vacuum receivers)	08223-1	872.00769.00		872.00830.00
1	Lid (Larger vacuum receivers)	NA	872.00783.00		-
	Lid (Tube Stub for Mezz. Mounted GH Hopper)	08223-2	-		-
2	1/8” NPT fitting		35085K, 35086K
3	1/4” NPT fitting		35154, 35155
4	Bulkhead		35146
5	Brass elbow		35118
6	24V DC Solenoid		33128

7	Dump cone	15370	33073	15237
8	Air cylinder	33126	33073			33011G

Figure 60: Typical Weigh Hopper Assembly Parts List

#	DESCRIPTION	010	020	040
1	WEIGH HOPPER	822.00382.00	822.00383.00	822.00384.00
2	LOAD CELL	61-1010E-10KG	A0564528	A0564546
3	LOAD CELL		872.00669.00
3	BRACKET		872.00669.00
	BRACKET

Figure 64: Typical Allen-Bradley Controller Main Parts List

#	Description	ALL MODELS
1	Allen-Bradley PLC MicroLogix 1500	A0565880
2	Thermocouple Input Card	A0565375
3	Allen-Bradley PLC Base Unit	A0565881
4	24V DC Power Supply	A0563932
5	12V DC Power Supply	739.00027.00
6	Alarm Light Yellow Strobe 24V DC	A0565889
7	Glass Fuse – 3.0 amp (115v unit)	A0542207
8	Ethernet Module (optional)	A0563939
9	Ethernet Module cable	A0565898
10	120V Light (power switch)	715.01034.02

Figure 65: Typical Allen-Bradley Display Main Parts List

	#	Description	All MODELS
	1	Allen-Bradley Panelview Touchscreen Display	892.001489.00
	1	PV 550 (DF-1 protocol)	892.001489.00
		PV 550 (DF-1 protocol)
	2	Enclosure Mounting Feet	A0567132
	3	Display – 8 ft Connection Cable	A0565856
	3	Display – 50 ft Connection Cable	A0565899
		Display – 50 ft Connection Cable	A0565899

Chapter 7: Appendix

49 of 60

Image 49

Contents GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference Unpacking and Inspection Shipping InfoEvent of Shipping Damage If the Shipment is Not CompleteReturns Warranty ReturnsCredit Returns Table of Contents Maintenance How to Use This Manual SafetySafety Symbols Used in this Manual Safety Tags and Warning Labels Description Wear Safety Glasses and Work Gloves Follow all Safety CodesGeneral Responsibility ResponsibilityOperator Responsibility Remember Reporting a Safety Defect Maintenance ResponsibilityFunctional Description AccessoriesModels Covered in This Manual General DescriptionCustomer Service Mechanical Features Typical Features and ComponentsController Features System Component Description Extruder Inductive Proximity SwitchSurge Hopper Weigh Hopper OpenFunction Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Ethernet Module Optional ComponentsPneumatic Slide Gate below surge hopper Safety FeaturesLow Level Proximity Sensors Mechanical Installation InstallationMounting Configurations Uncrating the EquipmentMachine Mount Electrical ConnectionsPneumatic Connections Initial Set-up Weigh Hopper InstallationMechanical Set-up Extruder RPM connectionDisplay Startup Screen Final ConnectionsController Set-up Recipe Page Start GH Controller Menu StructureWeigh Hopper Load Cell Calibration GH CalibrationDisplay Calibration Menu Screen WTP/RPM Calibration Hopper Size SetupHauloff Setup and Encoder Calibration Extruder SetupNetwork Setup Alarm SetupPanelView Configuration Screen Setting Date and TimeOperation GH-M Operation ProceduresOperator Displays Typical Operator Screen for GH Full Control system GH Full Control Operation ProceduresGH-F Gravimetric Feeder Operation Procedures Typical Manual Control Operator Screen Common ScreensAlarms with Descriptions Alarm FlagsPrint Inventory Preventative Maintenance Schedule MaintenanceCorrective Maintenance Preventative MaintenanceElectrical Internal Components of the Control PanelOutput Signals from Programmable Controller Input Signals to Programmable ControllerIntroduction TroubleshootingProblem Problem Corrective actionWarranty Specifications Warranty and Spare PartsWarranty Restrictions Warranty LiabilitiesAnnex B Information Customer ResponsibilitiesTypical Surge Hopper Assembly Parts List Passwords Addendum Service Supervisor InformationProgrammable Settings Typical Engineering Only Setup Screen Extruder Pulse Count Method Percent of hopper Method DefaultFull Hopper Method WTP/RPM FilterMechanical Options Screen Max Allowed WTP/RPMTypical Analog Options Analog options screen Diagnostics ScreenPassword Protection Customer Setup MenuAlarm Log UnitsAllen-Bradley Communications Manual Below are the items that can be accessed for the GH HopperAppendix Reload TOO Long Fixed Decimal Explanation Parts Department Service Department Sales DepartmentContract Department