Barco RCP-120 manual RCP120 Boot Menu Interface

Page 24

RCP120 Boot Menu Interface

Display Current Settings

Press 0 to display the current configuration settings for the panel. An example of the information returned is shown below:

Serial Number is SN9707xxxxxx

MAC address is xx:xx:xx:xx:xx:xx

DHCP is currently inactive

Static IP address is currently 192.168.0.100

Subnet Mask is currently 255.255.255.0

Gateway address is currently 192.168.0.1

Hostname is currently RCP-120

Master Controller IP address is currently 192.168.0.5

Serial Port Push Variable Name is currently

Configure IP Settings

Press 1 to enter the configuration dialog for DHCP or Manual IP Setup. Refer to Chapter 3, Network Configuration for more details concerning DHCP, Static IP, Subnet Mask and Gateway.

Set Password

Press 2 to enter the configuration dialog to change the admin password for the Web interface. The default setting is: admin

Set Host Name

Press 3 to enter the configuration dialog to set the Host Name of the RCP120. This host name will appear in the configuration menu on the FSN Controller for easy panel identification. This can be set at the users’ discretion to give a unique name to a panel. The maximum number of characters supported is 15. The default setting is: RCP20

Set Master Controller IP Address

Press 4 to enter the configuration dialog to set the Master Controller IP Address. This is the IP Address of the FSN Controller. If this is not set correctly, the RCP120 will not establish communication to the FSN Controller. The default setting is: 192.168.0.5

24	Remote Control Panel User’s Guide ● Rev 00

Image 24

Contents RCP120 Remote Control Panel User’s Guide Remote Control Panel User’s Guide Rev CopyrightCompany Address TrademarksPower Source Use the Proper Power CordDo Not Remove Covers or Panels Grounding the ProductTerms In This Manual and Equipment Marking Rev Date Description Approved By 09/11 586290 Initial ReleaseTable of Contents Universal Power Supply This page intentionally left blank Introduction OverviewConnectivity Diagram Application QuestionsRemote Control Panel Orientation RCP120 Front PanelRCP120 Rear Panel 2in Phoenix DC Power Input 4in Phoenix RS32 / IRLAN Installation Unpacking and InspectionWhat’s Included in the Box RCP120 Installation RCP120 Configuration Soft Reboot / Web Interface Password ResetConnecting to the RCP120 Web Interface Remote Control Panel User’s Guide Rev RCP120 Configuration RCP120 Configuration Web Interface Network ConfigurationStatus Change Admin Password Master Controller IP AddressSerial Port 1 Configuration / Baud Rate Serial Port 2 Configuration / Baud RateSerial Port 1 Auto Transmit Button Settings Update and Reboot / Reset DefaultsSeconds Before Default Setting is 0 No Timeout. Used to Delay Between Default Setting is 30 0.3 Seconds. Used toRCP120 Boot Menu Connecting to the Boot MenuOverview RCP120 Boot Menu Interface Restore Default Settings Discard Changes and RebootSave Changes and Reboot Selections Not SupportedRCP120 FSN Menu Orientation Assign Remote PanelsRemote Control Panel Table Figure below illustrates the Remote Control Panel TableDiscover Remote Panels Assign Aux Unassign Assign Remote Panels Menu FunctionsInfo Duplicate IP Address Notification Operations No Connection BehaviorDisplay IP/MAC Address and Firmware Version AUX Output Control Understanding Button MappingUnderstanding Button Color Button Color TableWorking with the RCP120 Remote Control Panel User’s Guide Rev Setting up the RCP120 to Control an Aux Output FSN System and Controller SetupRCP20 Setup Maintenance Operations Adding Additional RCP20 DevicesUnassign an Aux Output from an RCP20 Working with an Unconnected RCP20Controlling an Aux Output with the RCP120 Controlling a Standard Aux OutputControlling an Aux Output defined as a Mixer Program PreviewSoftware Update Overview Updating SoftwareHardware Requirements Downloading Software Via FTP SiteRCP20revision #.zip Via Web Site Updating RCP120 Software RCP20 Firmware UploadRemote Control Panel User’s Guide Rev Specifications Physical and Electrical SpecificationsCommunications Specifications Agency SpecificationsPower Connector Connector SpecificationsFigure below illustrates the 4pin Phoenix powe r connector Serial PortUniversal Power Supply Installing a Power Blade AdapterRemote Control Panel User’s Guide Rev Warranty Return Material Authorization RMAContact Information Contact Information Barco, IncSales Contact Information Barco N.V