Barco RCP-120 manual RCP120 Configuration, Soft Reboot / Web Interface Password Reset

Page 16

3. RCP120 Configuration

Soft Reboot / Web Interface Password Reset

To perform a soft reboot on the RCP120, press and hold buttons 2 and 5 for about five seconds.

To reset the Web Interface password back to “admin” on the RCP120, press and hold buttons 1, 4 and 6 while power is being applied.

Note

This reset procedure will not affect the parameters currently configured in the Web Interface. Use the “Reset Defaults” button in the Web Interface to reset the panel configuration parameters back to defaults.

Connecting to the RCP120 Web Interface

To connect to the RCP120 builtin web page, use th e following steps:

1.Connect the RCP120 and a computer to the same Ethe rnet switch.

2.Apply power to the RCP120.

3.To see the current IP address of the RCP120, press and hold buttons 11 and 12 for several seconds to display the:

a.IP Address

b.MAC Address

c.Firmware Version

4.Open a web browser on the computer.

5.Go to: http://<IP Address>

a.Example: http://192.168.0.100

16	Remote Control Panel User’s Guide ● Rev 00

Image 16

Contents RCP120 Remote Control Panel User’s Guide Remote Control Panel User’s Guide Rev CopyrightCompany Address TrademarksPower Source Use the Proper Power CordDo Not Remove Covers or Panels Grounding the ProductTerms In This Manual and Equipment Marking Rev Date Description Approved By 09/11 586290 Initial ReleaseTable of Contents Universal Power Supply This page intentionally left blank Introduction OverviewConnectivity Diagram Application QuestionsRCP120 Front Panel Remote Control Panel OrientationRCP120 Rear Panel 4in Phoenix RS32 / IR 2in Phoenix DC Power InputLAN Unpacking and Inspection InstallationWhat’s Included in the Box RCP120 Installation Soft Reboot / Web Interface Password Reset RCP120 ConfigurationConnecting to the RCP120 Web Interface Remote Control Panel User’s Guide Rev RCP120 Configuration Network Configuration RCP120 Configuration Web InterfaceStatus Change Admin Password Master Controller IP AddressSerial Port 2 Configuration / Baud Rate Serial Port 1 Configuration / Baud RateSerial Port 1 Auto Transmit Button Settings Update and Reboot / Reset DefaultsSeconds Before Default Setting is 0 No Timeout. Used to Delay Between Default Setting is 30 0.3 Seconds. Used toConnecting to the Boot Menu RCP120 Boot MenuOverview RCP120 Boot Menu Interface Restore Default Settings Discard Changes and RebootSave Changes and Reboot Selections Not SupportedRCP120 FSN Menu Orientation Assign Remote PanelsRemote Control Panel Table Figure below illustrates the Remote Control Panel TableDiscover Remote Panels Assign Aux Unassign Assign Remote Panels Menu FunctionsInfo Duplicate IP Address Notification No Connection Behavior OperationsDisplay IP/MAC Address and Firmware Version AUX Output Control Understanding Button MappingUnderstanding Button Color Button Color TableWorking with the RCP120 Remote Control Panel User’s Guide Rev FSN System and Controller Setup Setting up the RCP120 to Control an Aux OutputRCP20 Setup Maintenance Operations Adding Additional RCP20 DevicesUnassign an Aux Output from an RCP20 Working with an Unconnected RCP20Controlling an Aux Output with the RCP120 Controlling a Standard Aux OutputControlling an Aux Output defined as a Mixer Program PreviewUpdating Software Software Update OverviewHardware Requirements Via FTP Site Downloading SoftwareRCP20revision #.zip Via Web Site Updating RCP120 Software RCP20 Firmware UploadRemote Control Panel User’s Guide Rev Specifications Physical and Electrical SpecificationsCommunications Specifications Agency SpecificationsPower Connector Connector SpecificationsFigure below illustrates the 4pin Phoenix powe r connector Serial PortUniversal Power Supply Installing a Power Blade AdapterRemote Control Panel User’s Guide Rev Return Material Authorization RMA WarrantyContact Information Contact Information Barco, IncSales Contact Information Barco N.V