Barco RCP-120 manual Do Not Remove Covers or Panels, Power Source, Grounding the Product

Page 4

Operators Safety Summary

The general safety information in this summary is for operating personnel.

Do Not Remove Covers or Panels

There are no userserviceable parts within the unit . Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.

Power Source

This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply conductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the power cord is essential for safe operation.

Grounding the Product

This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired receptacle before connecting to the product input or output terminals. A protectiveground connection by way of the grounding conductor in the power cord is essential for safe operation.

Use the Proper Power Cord

Use only the power cord and connector specified for your product. Use only a power cord that is in good condition. Refer cord and connector changes to qualified service personnel.

Do Not Operate in Explosive Atmospheres

To avoid explosion, do not operate this product in an explosive atmosphere.

4	Remote Control Panel User’s Guide ● Rev 00

Image 4

Contents RCP120 Remote Control Panel User’s Guide Remote Control Panel User’s Guide Rev CopyrightCompany Address TrademarksPower Source Use the Proper Power CordDo Not Remove Covers or Panels Grounding the ProductTerms In This Manual and Equipment Marking Rev Date Description Approved By 09/11 586290 Initial ReleaseTable of Contents Universal Power Supply This page intentionally left blank Introduction OverviewConnectivity Diagram Application QuestionsRCP120 Front Panel Remote Control Panel OrientationRCP120 Rear Panel 4in Phoenix RS32 / IR 2in Phoenix DC Power InputLAN Unpacking and Inspection InstallationWhat’s Included in the Box RCP120 Installation Soft Reboot / Web Interface Password Reset RCP120 ConfigurationConnecting to the RCP120 Web Interface Remote Control Panel User’s Guide Rev RCP120 Configuration Network Configuration RCP120 Configuration Web InterfaceStatus Change Admin Password Master Controller IP AddressSerial Port 2 Configuration / Baud Rate Serial Port 1 Configuration / Baud RateSerial Port 1 Auto Transmit Button Settings Update and Reboot / Reset DefaultsSeconds Before Default Setting is 0 No Timeout. Used to Delay Between Default Setting is 30 0.3 Seconds. Used toConnecting to the Boot Menu RCP120 Boot MenuOverview RCP120 Boot Menu Interface Restore Default Settings Discard Changes and RebootSave Changes and Reboot Selections Not SupportedRCP120 FSN Menu Orientation Assign Remote PanelsRemote Control Panel Table Figure below illustrates the Remote Control Panel TableDiscover Remote Panels Assign Aux Unassign Assign Remote Panels Menu FunctionsInfo Duplicate IP Address Notification No Connection Behavior OperationsDisplay IP/MAC Address and Firmware Version AUX Output Control Understanding Button MappingUnderstanding Button Color Button Color TableWorking with the RCP120 Remote Control Panel User’s Guide Rev FSN System and Controller Setup Setting up the RCP120 to Control an Aux OutputRCP20 Setup Maintenance Operations Adding Additional RCP20 DevicesUnassign an Aux Output from an RCP20 Working with an Unconnected RCP20Controlling an Aux Output with the RCP120 Controlling a Standard Aux OutputControlling an Aux Output defined as a Mixer Program PreviewUpdating Software Software Update OverviewHardware Requirements Via FTP Site Downloading SoftwareRCP20revision #.zip Via Web Site Updating RCP120 Software RCP20 Firmware UploadRemote Control Panel User’s Guide Rev Specifications Physical and Electrical SpecificationsCommunications Specifications Agency SpecificationsPower Connector Connector SpecificationsFigure below illustrates the 4pin Phoenix powe r connector Serial PortUniversal Power Supply Installing a Power Blade AdapterRemote Control Panel User’s Guide Rev Return Material Authorization RMA WarrantyContact Information Contact Information Barco, IncSales Contact Information Barco N.V