Barco RCP-120 manual Table of Contents

Page 7

Table of Contents

Introduction	10
Overview	10
Connectivity Diagram	11
Application Questions	11
1. Remote Control Panel Orientation	12
RCP120 Front Panel	12
RCP120 Rear Panel	12
2. Installation	14
Unpacking and Inspection	14
What’s Included in the Box	14
RCP120 Installation	15
3. RCP120 Configuration	..................16
Soft Reboot / Web Interface Password Reset	16
Connecting to the RCP120 Web Interface	16
RCP120 Configuration Web Interface	19
Status	19
Network Configuration	19
Change Admin Password	20
Serial Port 1 Configuration / Baud Rate	21
Serial Port 2 Configuration / Baud Rate	21
Serial Port 1 Auto Transmit	21
Button Settings	22
Update and Reboot / Reset Defaults	22
RCP120 Boot Menu	23
Overview	23
Connecting to the Boot Menu	23
RCP120 Boot Menu Interface	24
Display Current Settings	24
Configure IP Settings	24
Set Password	24
Set Host Name	24
Set Master Controller IP Address	24
Restore Default Settings	25
Discard Changes and Reboot	25
Save Changes and Reboot	25
Selections Not Supported	25
4. RCP120 FSN Menu Orientation	............26
Assign Remote Panels	26
Remote Control Panel Table	27
Remote Control Panel User’s Guide ● Rev 00	7

Image 7

Contents RCP120 Remote Control Panel User’s Guide Copyright Remote Control Panel User’s Guide RevTrademarks Company AddressGrounding the Product Power SourceUse the Proper Power Cord Do Not Remove Covers or PanelsTerms In This Manual and Equipment Marking Description Approved By 09/11 586290 Initial Release Rev DateTable of Contents Universal Power Supply This page intentionally left blank Overview IntroductionApplication Questions Connectivity DiagramRCP120 Front Panel Remote Control Panel OrientationRCP120 Rear Panel 4in Phoenix RS32 / IR 2in Phoenix DC Power InputLAN Unpacking and Inspection InstallationWhat’s Included in the Box RCP120 Installation Soft Reboot / Web Interface Password Reset RCP120 ConfigurationConnecting to the RCP120 Web Interface Remote Control Panel User’s Guide Rev RCP120 Configuration Network Configuration RCP120 Configuration Web InterfaceStatus Master Controller IP Address Change Admin PasswordSerial Port 2 Configuration / Baud Rate Serial Port 1 Configuration / Baud RateSerial Port 1 Auto Transmit Delay Between Default Setting is 30 0.3 Seconds. Used to Button SettingsUpdate and Reboot / Reset Defaults Seconds Before Default Setting is 0 No Timeout. Used toConnecting to the Boot Menu RCP120 Boot MenuOverview RCP120 Boot Menu Interface Selections Not Supported Restore Default SettingsDiscard Changes and Reboot Save Changes and RebootAssign Remote Panels RCP120 FSN Menu OrientationFigure below illustrates the Remote Control Panel Table Remote Control Panel TableAssign Remote Panels Menu Functions Discover Remote Panels Assign Aux UnassignInfo Duplicate IP Address Notification No Connection Behavior OperationsDisplay IP/MAC Address and Firmware Version Understanding Button Mapping AUX Output ControlButton Color Table Understanding Button ColorWorking with the RCP120 Remote Control Panel User’s Guide Rev FSN System and Controller Setup Setting up the RCP120 to Control an Aux OutputRCP20 Setup Working with an Unconnected RCP20 Maintenance OperationsAdding Additional RCP20 Devices Unassign an Aux Output from an RCP20Controlling a Standard Aux Output Controlling an Aux Output with the RCP120Program Preview Controlling an Aux Output defined as a MixerUpdating Software Software Update OverviewHardware Requirements Via FTP Site Downloading SoftwareRCP20revision #.zip Via Web Site RCP20 Firmware Upload Updating RCP120 SoftwareRemote Control Panel User’s Guide Rev Physical and Electrical Specifications SpecificationsConnector Specifications Communications SpecificationsAgency Specifications Power ConnectorSerial Port Figure below illustrates the 4pin Phoenix powe r connectorInstalling a Power Blade Adapter Universal Power SupplyRemote Control Panel User’s Guide Rev Return Material Authorization RMA WarrantyContact Information Barco N.V Contact InformationBarco, Inc Sales Contact Information