Mitsubishi Electronics WD-62827 manual Appendix G Lamp Cartridge Replacement

Page 109

Appendix G: Lamp Cartridge Replacement

CAUTION

BURN DANGER!

During normal operation, the surfaces inside

the TV near the lamp are extremely hot.

TOUCH THE LAMP CARTRIDGE BY THE HANDLE ONLY

Do not touch the glass parts of the lamp cartridge.

CAUTION: If the television is on, press POWER to turn it off. Allow the television to cool for one hour before attempting to replace the lamp cartridge.

LAMP LIFE

The light source for this television is a lamp, which is part of a lamp cartridge assembly. The actual life of the lamp in this television can vary, based on the lamp itself, the air temperature around the TV while it is operating, and your viewing patterns. Warmer air or poor ventilation shortens the lamp life, as does turning the television on and off frequently.

When the end of the lamp’s average life is approaching, the TV displays a warning message for one minute when you power on the TV. The message will reappear the next five times you turn on the TV. If you wish, you may continue to use the current lamp until it stops working. After you change the lamp cartridge, you must reset the lamp reminder through the TV Setup menu. Otherwise, the warning message will appear again earlier than necessary. Mitsubishi warrants the lamp for one (1) year from date of the original purchase at retail. It is likely, however, that the lamp will last significantly longer than this.

TO ORDER A NEW LAMP:

While Under Warranty

After Warranty

 

 

Call (800) 332-2119. Please have model number, serial

Call (800) 553-7278. Order lamp part number

number, and TV purchase date available.

915P027010.

 

 

WARNING:

Do not remove the lamp cartridge immediately after turning off the television. You may get burned because of the lamp’s high temperature. Allow the television to cool for one hour before attempting to replace the lamp cartridge.

Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire. Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.

Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical shock. If any object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.

Install the lamp cartridge securely. Failure to do so may cause a fire.

Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.

The lamp in this product contains mercury. Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at: www.eiae.org.

IMPORTANT

Reset the lamp hours through the TV setup menu each time you replace the lamp cartridge. Otherwise, the lamp warning message will reappear sooner than necessary.

Appendices 109

Page 108 Page 110
Image 109
Page 108 Page 110
Contents TV Information Visit our website atWhile Under Warranty After Warranty TV Guide On Screen Access RequirementsStand Requirement TV Model Number Stand Model NumberFCC Declaration of Conformity Important Safeguards Important Safeguards Contents Mitsubishi DLP Projection Television Limited Warranty Mitsubishi Digital Electronics America, Inc Our ThanksChapter       TV AccessoriesSpecial Features of Your TV Memory Card Reader Widescreen Picture FormatTV Guide On Screen Interactive Program Guide System Input 3 and Ieee 1394 Input/Output Memory Card Reader and Front-Panel InputsCard Compatibility Front-Panel Indicator Lights Lamp Indicator ResetFront Control Panel Power/Timer Indicator Status IndicatorOverview Remote ControlSleep Timer Battery InstallationCare TV Back Panel IR Emitter NetCommandInput 1 . Component 1-3 InputsHdmi 1 DVI Analog AudioMonitorLink/RS-232C Control DTVLink/IEEEAdditional Information System Reset ButtonDemo Track Connecting Audio cables Connecting External Devices and NetCommand SetupWall Outlet Cable Connecting a Wall Outlet Cable or Cable BoxStandard Cable Box Can be used with a CableCARDAntennas with Separate UHF and VHF Leads Antenna with a Single LeadFor antennas with flat twin leads For cable or antenna with coaxial lead$3CBDLQBOFM VCR to an Antenna or Wall Outlet Cable Audio & VideoVCR to a Cable Box Audio & Video Connecting a VCR to a Cable Box Audio & VideoSatellite Receiver or Other Device with S-Video Receiver Stereo SystemTo connect an analog A/V receiver DVD Player with Component Video See Appendix a for component video signalDVI Device Hdmi Device Hdtv Cable Box or Satellite Receiver with Component VideoMonitorLink Control/RS-232C Device Connecting a MonitorLink Control/RS-232C DeviceTJFEEFWJDFT Connecting the IR Emitter NetCommand-Pin-Style vs -Pin-Style Connectors Connecting Compatible Ieee 139 DevicesConnection Styles Direct Device-To-Device StyleDigital Video Signals When Connecting Ieee 139 DevicesDigital Audio Signals Digital Control SignalHelpful Hints for NetCommand Connections NetCommand Setup and Editing NetCommand Introduction NetCommand Pre-Memorized Devices Using the Remote Control with NetCommandReceiver Cable Box SAT Satellite DVD Player ReceiverNetCommand Setup On-Screen Buttons 3D Graphical Menu System Remote Control ButtonsNetCommand Information Screen NetCommand Initial SetupWelcome Screen Device Setup Screen Setup Reminder NetCommand Initial Setup, Setup ReminderReview Screen Finish ScreenReceiver Screen Edit NetCommand Adding an A/V ReceiverReceiver Inputs Receiver AVR Learn Screen Receiver AVR Input Learn ScreenAudio Output to AVR Screen Name ScreenEdit NetCommand Screen Edit NetCommand Adding DevicesNew Device Screen Device Learn Screen Device ScreenConnection for Device Screen Device Advanced Learn ScreenIR Code for Device Screen VCR for Recordings ScreenRF Connection for Cable Screen Change Device Screen Edit NetCommand Changing or Deleting DevicesDelete Device Screen Ieee 1394 Devices and NetCommand Control Adding Ieee 1394 Devices Automatically Adding Ieee 1394 Devices AutomaticallyNew 1394 Device Screen Name for 1394 Device Screen Ieee 139 Device Type Screen Adding Ieee 139 Devices AutomaticallyConnection Screen Page NetCommand Functions PIP Device Selection Menu Device Selection MenuAudio Section Video SectionDevice Menu Using the Device Menu Button to Display MenusCableCARD Menu IR Controlled DevicesGuide and the Recording Setup Screen Using the Guide Button to Display ChannelView and MenusGuide Button Guide and the Device Selection MenuSetting up Recordings NetCommand-Controlled RecordingsTime-Delayed Recording Record ListTV Disc and A/V Disc Search by Time Direct VCR Recording from an Antenna or Cable SourceTV Disc and A/V Disc Track List Screen Copy-Protected MaterialUsing the Remote Control with TV Disc or an A/V Disc Using TV Disc and A/V DiscsCopying or Moving TV Disc or A/V Disc Recordings Setting up a Non-Recording Peer-to- Peer Connection What is a Peer-to-Peer Connection?Cancelling a Peer-to-Peer Connection Peer-to-Peer ConnectionsTV Menu Operations Main Menu Language Setup MenuMemorize Channels ClockLamp Reminder TimerSoftware Version Remote Control Transport Buttons NetCommand MenuEdit Icon OrderTV Pause Controlling TV Pause FeaturesTV Pause with TimeShuttle TimeShuttleTimeShuttle and TV Disc Recordings To Turn Off TimeShuttleTime-Delayed Recording Recording SetupRecord Menu RecordCancel Scheduled Recordings Default Digital Record DeviceTV Guide On Screen and the Record List Analog RecordingsChannel Menu SQV SuperQuickView Signal StrengthCaptions Menu Digital SettingsAnalog Captions BackgroundSize FontsColor Opacity FontSetting V-Chip Options Setting a Pass CodeChip Lock Menu Chip Lock Menu OverviewLock by Time V-CHIP ButtonFront Button Lock Bypassing V‑Chip Lock and Lock by TimeContent Categories Chip Signal InformationChip Ratings Audio/Video Menu Analog and Digital Audio Settings Audio SettingsAnalog-Only Audio Settings Digital-Only Audio SettingsVideo Settings Video SettingsPC Video Settings Page CableCARD MediaCommand and Memory Card PlaybackCableCARD Using a CableCARDCableCARD Technology Memory Card Slots MediaCommand and Memory Card PlaybackMedia Setup Menu Media Command and Memory Card PlaybackFor Jpeg Picture Slide Show Setup For MP3 or WMA Audio Playlist SetupOperation of PIP and POP TV Display Formats Signal DefinitionsDVD Definitions Format Definitions57%JTQMBZ Analog Program On-Screen InformationDigital Program TV Disc or Digital Ieee 1394 DeviceUsing the TV with a PC See Appendix a for signal compatibility Connecting a PCComputer with an Hdmi Monitor Output Computer with a 15-Pin Monitor Output Computer with a DVI Monitor OutputModels WD-62927 and WD-73927 Adjusting Image Resolution Adjusting Image ResolutionPC Display Formats Page Appendix F Cleaning and Service Appendix a SpecificationsAppendix J Troubleshooting TV Specifications Appendix a SpecificationsInputs Outputs Appendix B NetCommand Specialized Device Keys Bypassing the V-Chip Lock Appendix CBypassing the V-Chip Lock Deactivating the Front Button LockThis page intentionally blank Programming the Remote to Control NetCommand A/V Products Appendix D Remote Control Programming CodesReceivers Cable BoxesSatellite Receivers/SAT/DTV DVD PlayersVCRs Cable/SAT/DTV position TV positionVCR position DVD positionNetCommand Compatible Traditional Devices Analog Appendix E Device Control with NetCommandIeee 1394 Devices When an Ieee 1394 Device is Viewed or PlayedAppendix F Cleaning and Service Do not touch the glass parts of the lamp cartridge Appendix G Lamp Cartridge ReplacementWash Your Hands THOROUGHLY, AS this Lamp Contains Mercury See detail Appendix H Diamond Shield Removal and InstallationNotched edge Down Install TrimTV Screen Raised Lip ChannelStep Hook the top End over Raised lip Install the Diamond ShieldStep Hook the lower End over Raised lip Pry up from the notches at both endsAnalog VCR Connected to Audio and Video Record Outputs Appendix I Recording and Viewing CombinationsDigital VCR or A/V Disc Connected to IEEE-1394 Port Symptom Remarks Appendix J TroubleshootingGeneral TV Operation PIP Picture IndicatorsRecording SoundExcessive digital artifacts when viewing an Ieee TV Guide On Screen Trademark and License Information Mitsubishi TV Software 123 Mitsubishi DLP Projection Television Limited Warranty124 This Limited Warranty does not CoverIndex IndexIndex Page Website Mail MDEAservice@mdea.com
Related manuals
Manual 86 pages 7.9 Kb
Top Page Image Contents