Mitsubishi Electronics WD-62827 manual V-CHIP Button, Lock by Time, Front Button Lock

Page 77

V-Chip Lock Menu, continued

5.Press ADJUST to move to the TV content categories.

•Press ADJUST or to move between categories.

•Press ENTER to add check marks to the TV content categories you want to block.

6.Press ADJUST to move to the Programs Not Rated box. Press ENTER to add or delete a check mark to allow or block programs that are not rated.

NOTE: Use care when choosing to block unrated programming. News programs and emergency bulletins carry the “None” or “NR” (Not Rated) V‑Chip rating, and these are blocked with this option active.

7.Press ADJUST to move to the Movie Rating box. Press ADJUST or to select the movie rating level you want to allow. See the next page for detailed information on rating guidelines.

8.To set the time of day when these restrictions will be in effect, press ADJUST to move to the Start box. To set the time:

a.With the highlight on the hour number, press ADJUST or repeatedly to change the hour. You can also just press and hold to change the hour.

b.Press ENTER to move the highlight to the minutes.

c.With the highlight on the minutes number, press ADJUST or repeatedly to change the minutes. Just press and hold to move quickly through the numbers.

d.Press ENTER to move the highlight to the am/ pm option. Press ADJUST or to make a selection.

9.Press TV MENU to save the settings and close the menu.

NOTE: To make the V-Chip restrictions active twenty- four hours a day, set the V-Chip Start and Stop to the same time.

The V-CHIP Button

Press the V-CHIP button on the remote control to turn the V‑Chip lock on and off without going through the menu. A screen will appear prompting you for your pass code. To change V-Chip settings, you must open the V‑Chip Lock Menu and then open the V-Chip menu.

Lock by Time

Lock by Time allows you to entirely block use of the TV during specified hours. During the lock time, you must use your pass code to view the TV. To lock the TV by time:

1.Press ADJUST or to select On or Off for Lock by Time.

2.Press ADJUST to move to the Lock Time box.

a.With the highlight on the hour number, press ADJUST or repeatedly to change the hour. You can also just press and hold to change the hour.

b.Press ENTER to move the highlight to the minutes.

c.With the highlight on the minutes number, press ADJUST or repeatedly to change the minutes. Just press and hold to move quickly through the numbers.

d.Press ENTER to move the highlight to the am/ pm option. Press ADJUST or to make a selection.

To make Lock by Time active 24 hours a day, set the Lock and Unlock Times to the same time.

Front Button Lock

Figure 20

Front Button Lock lets you disable controls on the front panel to prevent inadvertent changes to TV settings. Select On to disable the buttons and select Off to restore their operation.

To disable the front button lock without using the remote control, press and hold the MENU button on the front panel for more than eight seconds. If the TV is on, a message will display confirming release of the Front Button Lock.

Bypassing V‑Chip Lock and Lock by Time

If you try to watch blocked programming, a notice appears prompting you for a pass code. To use the TV:

•Input your four-digit pass code and press ENTER.

•Change to a channel airing an allowed program or change to another device.

If you try to use the TV when it is locked by time, a similar screen appears, prompting you for your pass code.

To reactivate the V-Chip lock or TV lock by time after using the pass code, power the TV off and then on.

Chapter 5. TV Menu Operations

77

Page 76 Page 78
Image 77
Page 76 Page 78
Contents TV Information Visit our website atWhile Under Warranty After Warranty TV Guide On Screen Access RequirementsStand Requirement TV Model Number Stand Model NumberFCC Declaration of Conformity Important Safeguards Important Safeguards Contents Mitsubishi DLP Projection Television Limited Warranty Mitsubishi Digital Electronics America, Inc Our ThanksChapter       TV AccessoriesSpecial Features of Your TV TV Guide On Screen Interactive Program Guide System Widescreen Picture FormatMemory Card Reader Card Compatibility Memory Card Reader and Front-Panel InputsInput 3 and Ieee 1394 Input/Output Front Control Panel ResetFront-Panel Indicator Lights Lamp Indicator Power/Timer Indicator Status IndicatorOverview Remote ControlCare Battery InstallationSleep Timer TV Back Panel IR Emitter NetCommandInput 1 . Component 1-3 InputsHdmi 1 DVI Analog AudioMonitorLink/RS-232C Control DTVLink/IEEEDemo Track System Reset ButtonAdditional Information Connecting Audio cables Connecting External Devices and NetCommand SetupWall Outlet Cable Connecting a Wall Outlet Cable or Cable BoxStandard Cable Box Can be used with a CableCARDAntennas with Separate UHF and VHF Leads Antenna with a Single LeadFor antennas with flat twin leads For cable or antenna with coaxial lead$3CBDLQBOFM VCR to an Antenna or Wall Outlet Cable Audio & VideoVCR to a Cable Box Audio & Video Connecting a VCR to a Cable Box Audio & VideoTo connect an analog A/V receiver Receiver Stereo SystemSatellite Receiver or Other Device with S-Video DVI Device See Appendix a for component video signalDVD Player with Component Video Hdmi Device Hdtv Cable Box or Satellite Receiver with Component VideoMonitorLink Control/RS-232C Device Connecting a MonitorLink Control/RS-232C DeviceTJFEEFWJDFT Connecting the IR Emitter NetCommand-Pin-Style vs -Pin-Style Connectors Connecting Compatible Ieee 139 DevicesConnection Styles Direct Device-To-Device StyleDigital Video Signals When Connecting Ieee 139 DevicesDigital Audio Signals Digital Control SignalHelpful Hints for NetCommand Connections NetCommand Setup and Editing NetCommand Introduction NetCommand Pre-Memorized Devices Using the Remote Control with NetCommandReceiver Cable Box SAT Satellite DVD Player ReceiverNetCommand Setup On-Screen Buttons 3D Graphical Menu System Remote Control ButtonsWelcome Screen NetCommand Initial SetupNetCommand Information Screen Device Setup Screen Setup Reminder NetCommand Initial Setup, Setup ReminderReview Screen Finish ScreenReceiver Inputs Edit NetCommand Adding an A/V ReceiverReceiver Screen Receiver AVR Learn Screen Receiver AVR Input Learn ScreenAudio Output to AVR Screen Name ScreenNew Device Screen Edit NetCommand Adding DevicesEdit NetCommand Screen Device Learn Screen Device ScreenConnection for Device Screen Device Advanced Learn ScreenRF Connection for Cable Screen VCR for Recordings ScreenIR Code for Device Screen Delete Device Screen Edit NetCommand Changing or Deleting DevicesChange Device Screen Ieee 1394 Devices and NetCommand Control New 1394 Device Screen Name for 1394 Device Screen Adding Ieee 1394 Devices AutomaticallyAdding Ieee 1394 Devices Automatically Connection Screen Adding Ieee 139 Devices AutomaticallyIeee 139 Device Type Screen Page NetCommand Functions PIP Device Selection Menu Device Selection MenuAudio Section Video SectionDevice Menu Using the Device Menu Button to Display MenusCableCARD Menu IR Controlled DevicesGuide and the Recording Setup Screen Using the Guide Button to Display ChannelView and MenusGuide Button Guide and the Device Selection MenuSetting up Recordings NetCommand-Controlled RecordingsTime-Delayed Recording Record ListTV Disc and A/V Disc Search by Time Direct VCR Recording from an Antenna or Cable SourceTV Disc and A/V Disc Track List Screen Copy-Protected MaterialCopying or Moving TV Disc or A/V Disc Recordings Using TV Disc and A/V DiscsUsing the Remote Control with TV Disc or an A/V Disc Setting up a Non-Recording Peer-to- Peer Connection What is a Peer-to-Peer Connection?Cancelling a Peer-to-Peer Connection Peer-to-Peer ConnectionsTV Menu Operations Main Menu Language Setup MenuMemorize Channels ClockSoftware Version TimerLamp Reminder Remote Control Transport Buttons NetCommand MenuEdit Icon OrderTV Pause Controlling TV Pause FeaturesTV Pause with TimeShuttle TimeShuttleTimeShuttle and TV Disc Recordings To Turn Off TimeShuttleTime-Delayed Recording Recording SetupRecord Menu RecordCancel Scheduled Recordings Default Digital Record DeviceTV Guide On Screen and the Record List Analog RecordingsChannel Menu SQV SuperQuickView Signal StrengthCaptions Menu Digital SettingsAnalog Captions BackgroundSize FontsColor Opacity FontSetting V-Chip Options Setting a Pass CodeChip Lock Menu Chip Lock Menu OverviewLock by Time V-CHIP ButtonFront Button Lock Bypassing V‑Chip Lock and Lock by TimeChip Ratings Chip Signal InformationContent Categories Audio/Video Menu Analog and Digital Audio Settings Audio SettingsAnalog-Only Audio Settings Digital-Only Audio SettingsPC Video Settings Video SettingsVideo Settings Page CableCARD MediaCommand and Memory Card PlaybackCableCARD Technology Using a CableCARDCableCARD Memory Card Slots MediaCommand and Memory Card PlaybackMedia Setup Menu Media Command and Memory Card PlaybackFor Jpeg Picture Slide Show Setup For MP3 or WMA Audio Playlist SetupOperation of PIP and POP TV Display Formats Signal DefinitionsDVD Definitions Format Definitions57%JTQMBZ Analog Program On-Screen InformationDigital Program TV Disc or Digital Ieee 1394 DeviceUsing the TV with a PC Computer with an Hdmi Monitor Output Connecting a PCSee Appendix a for signal compatibility Models WD-62927 and WD-73927 Computer with a DVI Monitor OutputComputer with a 15-Pin Monitor Output Adjusting Image Resolution Adjusting Image ResolutionPC Display Formats Page Appendix J Troubleshooting Appendix a SpecificationsAppendix F Cleaning and Service Inputs Appendix a SpecificationsTV Specifications Outputs Appendix B NetCommand Specialized Device Keys Bypassing the V-Chip Lock Appendix CBypassing the V-Chip Lock Deactivating the Front Button LockThis page intentionally blank Programming the Remote to Control NetCommand A/V Products Appendix D Remote Control Programming CodesReceivers Cable BoxesVCRs DVD PlayersSatellite Receivers/SAT/DTV Cable/SAT/DTV position TV positionVCR position DVD positionNetCommand Compatible Traditional Devices Analog Appendix E Device Control with NetCommandIeee 1394 Devices When an Ieee 1394 Device is Viewed or PlayedAppendix F Cleaning and Service Do not touch the glass parts of the lamp cartridge Appendix G Lamp Cartridge ReplacementWash Your Hands THOROUGHLY, AS this Lamp Contains Mercury See detail Appendix H Diamond Shield Removal and InstallationNotched edge Down Install TrimTV Screen Raised Lip ChannelStep Hook the top End over Raised lip Install the Diamond ShieldStep Hook the lower End over Raised lip Pry up from the notches at both endsDigital VCR or A/V Disc Connected to IEEE-1394 Port Appendix I Recording and Viewing CombinationsAnalog VCR Connected to Audio and Video Record Outputs General TV Operation Appendix J TroubleshootingSymptom Remarks PIP Picture IndicatorsRecording SoundExcessive digital artifacts when viewing an Ieee TV Guide On Screen Trademark and License Information Mitsubishi TV Software 123 Mitsubishi DLP Projection Television Limited Warranty124 This Limited Warranty does not CoverIndex IndexIndex Page Website Mail MDEAservice@mdea.com
Related manuals
Manual 86 pages 7.9 Kb
Top Page Image Contents