One for All URC-9964B00 manual Changing Volume Lock, Optimizing IR/RF Base Station Reception

Page 27

OFA Kameleon wRF UG rev 3.fm Page 27 Monday, September 13, 2004 11:18 AM

USER’S GUIDE

OPTIMIZING IR/RF BASE STATION RECEPTION

Here are some adjustment tips for optimizing the operation of your IR/RF Base Station:

•Aim the OFA Kameleon 8-Device Remote with RF toward the room where the IR/RF Base Station is located.

•Do not position the IR/RF Base Station near metal objects, such as heat ducts. Metal can absorb RF signals.

•Make sure the batteries in the OFA Kameleon 8-Device Remote with RF are fully charged. Try replacing them if you are not sure (see “Installing Batteries” on page 4). Weak batteries will affect the signal range.

•Make sure that the OFA Kameleon 8-Device Remote with RF is not being affected by other RF transmissions (e.g., garage door openers, cordless telephones, etc.).

NOTE: The tests for range limits of the OFA Kameleon 8-Device Remote with RF and the IR/RF Base Station were conducted in open-air distance tests. Actual signal distance will be based on the construction of the building the unit is being used in, as well as other factors, such as outside interference.

CHANGING VOLUME LOCK

The OFA Kameleon 8-Device Remote with RF is set at the factory for independent volume control of each selected device.

However, you may change the Volume Lock setting to Global Volume Lock so that a device’s volume is locked to one mode (e.g., to control TV volume in all other modes). After that you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.

LOCKING VOLUME CONTROL TO ONE MODE (GLOBAL VOLUME LOCK)

1.Press and hold SETUP until the two bottom IR

segments flash twice. The Program Keys appear as SETUP flashes repeatedly.

	Changing Volume Lock		27

Image 27

Contents User’s Guide Kameleon 8-DEVICE Remote with RF Introduction Pressing any key turns on all keys and icons Installing BatteriesHOW Kameleon Works Features And Functions Features and FunctionsPress Mute once to turn the sound off or on KEY ChartsUse CH or CH to select the next higher or lower channel Device Cursor and OK KeysControl PVR/DVR video PVR mode, use the Live Transport Keys toUSER’S Guide Device KEY Controls These Devices Device TableAdjusting the Display Adjusting BrightnessProgram Keys appear Adjusting HOW Long the Screen Light is on Adjusting The DisplaySeconds Press Other once.The Other programming screen appears Setting the Vibration SwitchUsing the Number Keys, enter 9 8 Programming Device ControlSAT, CD, TV, DVD, AUDIO, VCR, or PVR Selected device key animatesProgramming Device Control Audio Code CBL/SAT Code Programming Combo Device Control Searching for Your Code One or moreIf desired, use to try a previous code Checking The Codes Using the Number Keys, enter 9 9Checking the Codes Bottom two IR segments flash twiceUsing the Home Theater Mode Control OrganizationPAGE-, MENU, INFO, GUIDE, Exit DVD Press and hold Setup until the two bottom IRUSER’S Guide Using the IR/RF Base Station Setting UP the IR/RF Base Station Using the IR/RF Base Station Adding the IR Signal Extension Cord Power Cord Antenna IR LensDistance may vary Optimizing IR/RF Base Station Reception Changing Volume LockLocking Volume Control to ONE Mode Global Volume Lock Changing Volume LockIndividual Volume Unlock Using Macros Unlocking ALL Volume Control Restoring Default SettingPressand holdSETUP until the two bottom IR Programming a Favorite Channel Macro Programming a Master Power Macro in the Home Theater Mode Using Learning Learning PrecautionsClearing a Macro Programming a Learning KEY Deleting a Single Learning KEY Deleting ALL Learned Keys in a Specific Mode Using Keymover Reassigning Device KeysReassigning Device Keys Press VOL Programming KeymoverTwo bottom IR segments flash twice AppearsRestoring ALL Keymoved Keys in a Single Mode Restoring a Single Keymoved KEYPerform steps 1 through 3 of Programming Keymover, above Programming Favorite Channel Scan Using Channel ScanRestoring Factory Default Settings Restoring Factory Default SettingsClearing ALL Custom Programming Manufacturer’s Codes Setup Codes for Audio AmplifiersSetup Codes for Audio Receivers MANUFACTURER’S CodesSetup Codes for CD Players Setup Codes for Cable BoxesNSM Setup Codes for DVD PlayersSetup Codes for Home Automation Setup Codes for DVD PlayerPlayers Codes Setup Codes for PvrsSKY Setup Codes for TVSJCB SVA Setup Codes for TV/DVD Player Combos DVD CodesSetup Codes for Vcrs Setup Codes for TV/VCR/DVD Player CombosHI-Q Consumer Help-Line 330 Setup Codes for Video AccessoriesSetup Codes for CABLE/DVR Combos About UpgradingUpgrade Exclusions Upgrade ProcedureTroubleshooting USER’S Guide Device Menu Screens Programming Main MenuDevice Menu Screens Audio Surround Menu Audio Presets Menu AUX PVR/VOD M ENU CBL/SAT PVR/VOD M ENU DVD Main Menu PVR Main Menu TV M ENU VCR M ENU VCR Main MenuCustomer Support Battery USE and Safety About Battery LifeBattery Use And Safety Additional Information SpecificationsRemote Control Dimensions IR/RF Base Station Dimensions