One for All URC-9964B00 manual SAT, CD, TV, DVD, AUDIO, VCR, or PVR, Selected device key animates

Page 16

OFA Kameleon wRF UG rev 3.fm Page 16 Monday, September 13, 2004 11:18 AM

KAMELEON 8-DEVICE REMOTE WITH RF

To control devices other than the default brands, perform the following steps; otherwise skip this section.

NOTE: . To control a Combo device, perform the instructions in “Programming DVD Player/VCR Combo Control” on page 17.

1.Turn on a device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).

NOTE: Read steps 2 through 9 completely before proceeding. Before starting step 2, review the “Manufacturer’s Codes” (starting on page 42). Brands are listed alphabetically in order of most popular ones first. Highlight or write down the devices and the codes you wish to program.

1.Press and hold SETUP until the two bottom IR segments flash twice. The Program Keys appear as SETUP flashes repeatedly

NOTE: . If the display turns off due to inactivity, the remote control exits programming and return to the last-selected device menu screen. To start programming again, repeat this step. To stop programming at any time, press HOME once to return to the Program Keys screen. Press HOME once more to exit completely.

2.Press DEV SET once. The Device Setup programming screen appears:

3.Press a device key once (i.e., AUX, CBL/

SAT, CD, TV, DVD, AUDIO, VCR, or PVR).

The selected device key animates.

NOTE: Refer to the Device Table on page 12 when choosing a device key for programming.

4. Use the Manufacturer’s Codes (starting on page 42) to locate the type of device and brand name and then use the Number Keys to enter the first code for your device. The bottom two IR segments flash twice.

NOTE: If the bottom two IR segments displayed one long flash, a mistake has occurred. Try entering the code again.

16

 

 

Programming Device Control

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 16
Contents User’s Guide Kameleon 8-DEVICE Remote with RF Introduction Installing Batteries Pressing any key turns on all keys and iconsHOW Kameleon Works Features and Functions Features And FunctionsKEY Charts Press Mute once to turn the sound off or onUse CH or CH to select the next higher or lower channel Cursor and OK Keys DevicePVR mode, use the Live Transport Keys to Control PVR/DVR videoUSER’S Guide Device Table Device KEY Controls These DevicesAdjusting Brightness Adjusting the DisplayProgram Keys appear Adjusting The Display Adjusting HOW Long the Screen Light is onSeconds Setting the Vibration Switch Using the Number Keys, enter 9 8Programming Device Control Press Other once.The Other programming screen appearsSelected device key animates SAT, CD, TV, DVD, AUDIO, VCR, or PVRProgramming Device Control Audio Code CBL/SAT Code Programming Combo Device Control One or more Searching for Your CodeIf desired, use to try a previous code Using the Number Keys, enter 9 9 Checking the CodesBottom two IR segments flash twice Checking The CodesControl Organization Using the Home Theater ModePAGE-, MENU, INFO, GUIDE, Exit Press and hold Setup until the two bottom IR DVDUSER’S Guide Setting UP the IR/RF Base Station Using the IR/RF Base StationUsing the IR/RF Base Station Power Cord Antenna IR Lens Adding the IR Signal Extension CordDistance may vary Changing Volume Lock Locking Volume Control to ONE Mode Global Volume LockChanging Volume Lock Optimizing IR/RF Base Station ReceptionIndividual Volume Unlock Unlocking ALL Volume Control Restoring Default Setting Using MacrosPressand holdSETUP until the two bottom IR Programming a Favorite Channel Macro Programming a Master Power Macro in the Home Theater Mode Learning Precautions Using LearningClearing a Macro Programming a Learning KEY Deleting a Single Learning KEY Deleting ALL Learned Keys in a Specific Mode Reassigning Device Keys Using KeymoverReassigning Device Keys Programming Keymover Two bottom IR segments flash twiceAppears Press VOLRestoring a Single Keymoved KEY Restoring ALL Keymoved Keys in a Single ModePerform steps 1 through 3 of Programming Keymover, above Using Channel Scan Programming Favorite Channel ScanRestoring Factory Default Settings Restoring Factory Default SettingsClearing ALL Custom Programming Setup Codes for Audio Amplifiers Setup Codes for Audio ReceiversMANUFACTURER’S Codes Manufacturer’s CodesSetup Codes for Cable Boxes Setup Codes for CD PlayersSetup Codes for DVD Players NSMSetup Codes for DVD Player Setup Codes for Home AutomationSetup Codes for Pvrs Players CodesSetup Codes for TVS SKYJCB Setup Codes for TV/DVD Player Combos DVD Codes SVASetup Codes for TV/VCR/DVD Player Combos Setup Codes for VcrsHI-Q Setup Codes for Video Accessories Setup Codes for CABLE/DVR CombosAbout Upgrading Consumer Help-Line 330Upgrade Procedure Upgrade ExclusionsTroubleshooting USER’S Guide Programming Main Menu Device Menu ScreensDevice Menu Screens Audio Surround Menu Audio Presets Menu AUX PVR/VOD M ENU CBL/SAT PVR/VOD M ENU DVD Main Menu PVR Main Menu TV M ENU VCR Main Menu VCR M ENUCustomer Support About Battery Life Battery USE and SafetyBattery Use And Safety Specifications Remote Control DimensionsIR/RF Base Station Dimensions Additional Information