One for All URC-9964B00 manual Troubleshooting

Page 54

OFA Kameleon wRF UG rev 3.fm Page 54 Monday, September 13, 2004 11:18 AM

KAMELEON 8-DEVICE REMOTE WITH RF

TROUBLESHOOTING

PROBLEM:

No display at all times.

SOLUTION:

Replace batteries with four new AA alkaline batteries.

 

 

PROBLEM:

The bottom two IR indicator segments are flashing.

SOLUTION:

Replace batteries with four new AA alkaline batteries.

 

 

PROBLEM:

No display when programming.

SOLUTION:

Display has turned off due to inactivity. Start programming

 

again and do not pause while performing instructions.

 

 

PROBLEM:

During programming, the two bottom IR segments display

 

a long flash.

SOLUTION:

An invalid entry has occurred. Check the keys to be pressed

 

and start program again.

 

 

PROBLEM:

How do I stop programming?

SOLUTION:

Press HOME once to return to the Program Keys screen.

 

Press HOME once more to exit completely.

 

 

PROBLEM:

The unit does not control home entertainment devices or

 

commands are not working properly.

SOLUTION:

Try all listed codes for the device brands being set up.Make

 

sure they can be operated with an infrared remote control.

 

 

PROBLEM:

Tried Searching For Your Code method and still could not

 

find a working code.

SOLUTION:

Perform Restoring Factory Default Settings on page 40. Then

 

repeat Searching For Your Code on page 19.

 

 

PROBLEM:

Cannot program a macro onto M1 – M4 or POWER keys.

SOLUTION:

Make sure the total number of key presses being

 

programmed is less than 15.

 

 

PROBLEM:

Power macro does not execute.

SOLUTION:

First, press the Home Theater key once, then press POWER

 

once.

 

 

54

 

 

 

Troubleshooting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 54
Contents User’s Guide Kameleon 8-DEVICE Remote with RF Introduction Installing Batteries Pressing any key turns on all keys and iconsHOW Kameleon Works Features and Functions Features And FunctionsKEY Charts Press Mute once to turn the sound off or onUse CH or CH to select the next higher or lower channel Cursor and OK Keys DevicePVR mode, use the Live Transport Keys to Control PVR/DVR videoUSER’S Guide Device Table Device KEY Controls These DevicesAdjusting the Display Adjusting BrightnessProgram Keys appear Adjusting HOW Long the Screen Light is on Adjusting The DisplaySeconds Programming Device Control Setting the Vibration SwitchUsing the Number Keys, enter 9 8 Press Other once.The Other programming screen appearsSAT, CD, TV, DVD, AUDIO, VCR, or PVR Selected device key animatesProgramming Device Control Audio Code CBL/SAT Code Programming Combo Device Control Searching for Your Code One or moreIf desired, use to try a previous code Bottom two IR segments flash twice Using the Number Keys, enter 9 9Checking the Codes Checking The CodesUsing the Home Theater Mode Control OrganizationPAGE-, MENU, INFO, GUIDE, Exit Press and hold Setup until the two bottom IR DVDUSER’S Guide Using the IR/RF Base Station Setting UP the IR/RF Base StationUsing the IR/RF Base Station Power Cord Antenna IR Lens Adding the IR Signal Extension CordDistance may vary Changing Volume Lock Changing Volume LockLocking Volume Control to ONE Mode Global Volume Lock Optimizing IR/RF Base Station ReceptionIndividual Volume Unlock Using Macros Unlocking ALL Volume Control Restoring Default SettingPressand holdSETUP until the two bottom IR Programming a Favorite Channel Macro Programming a Master Power Macro in the Home Theater Mode Using Learning Learning PrecautionsClearing a Macro Programming a Learning KEY Deleting a Single Learning KEY Deleting ALL Learned Keys in a Specific Mode Using Keymover Reassigning Device KeysReassigning Device Keys Appears Programming KeymoverTwo bottom IR segments flash twice Press VOLRestoring ALL Keymoved Keys in a Single Mode Restoring a Single Keymoved KEYPerform steps 1 through 3 of Programming Keymover, above Using Channel Scan Programming Favorite Channel ScanRestoring Factory Default Settings Restoring Factory Default SettingsClearing ALL Custom Programming MANUFACTURER’S Codes Setup Codes for Audio AmplifiersSetup Codes for Audio Receivers Manufacturer’s CodesSetup Codes for Cable Boxes Setup Codes for CD PlayersSetup Codes for DVD Players NSMSetup Codes for DVD Player Setup Codes for Home AutomationSetup Codes for Pvrs Players CodesSetup Codes for TVS SKYJCB Setup Codes for TV/DVD Player Combos DVD Codes SVASetup Codes for TV/VCR/DVD Player Combos Setup Codes for VcrsHI-Q About Upgrading Setup Codes for Video AccessoriesSetup Codes for CABLE/DVR Combos Consumer Help-Line 330Upgrade Procedure Upgrade ExclusionsTroubleshooting USER’S Guide Device Menu Screens Programming Main MenuDevice Menu Screens Audio Surround Menu Audio Presets Menu AUX PVR/VOD M ENU CBL/SAT PVR/VOD M ENU DVD Main Menu PVR Main Menu TV M ENU VCR Main Menu VCR M ENUCustomer Support Battery USE and Safety About Battery LifeBattery Use And Safety IR/RF Base Station Dimensions SpecificationsRemote Control Dimensions Additional Information