Philips DVDR80/99 owner manual DV S-VIDEO Video Audio Left Right

Page 17

Hookups (cont’d) 17

Connecting to Other Equipment

Dubbing Videotape to a DVD+R/DVD+RW

OPEN/CLOSE

STANDBY-ON

You can connect a Video Cassette Recorder (VCR), Camcorder, or DVD Player to the Recorder’s CAM or IN-EXT jacks.

A sample connection with a Camcorder is shown here, using the CAM 1 AUDIO/VIDEO IN jacks on the front of the Recorder. These jacks are the most easily accessible. Other equipment will con- nect similarly, but this is a common connection possibility.

You will need this connection to copy videotapes onto a DVD+R or DVD+RW. There are more Component Video, S-Video, Digital Video, and Audio In jacks on the front and rear of the Recorder. If your other equipment has these jacks, use them instead. Use the IN-EXT jacks on the rear of the Recorder for permanent connections.That will hide the cables from view.

1 Connect the DVD Recorder directly to your TV. Choose a connection from pages 10-16.

2 To access the jacks on the front of the Recorder, flip down the door that covers the jacks. Press where the door is marked OPEN :.

3 Connect a video cable to the VIDEO OUT jack of your Camcorder and to the yellow CAM 1 VIDEO IN jack on the front of the DVD Recorder. Use an RCA-style video cable, which is usually marked with yellow. (One video cable is supplied with the Recorder.)

4 Connect audio cables to the AUDIO OUT jacks of your Camcorder and to the red and white CAM 1 AUDIO IN jacks on the front of the DVD Recorder. Most audio cables are marked with red and white. Match the cable colors to the jack colors. (One pair of audio cables is supplied with the DVD Recorder.)

5 When all connections are complete, connect all the equipment to power. Turn on all the equipment. Press STANDBY-ON y on the front of the DVD Recorder to turn it on.

6 Set your TV to the correct Video In channel. This will be channel 3 or 4 or a specific Video In channel, depending on your connection between the Recorder and the TV. Refer to the connection details on pages 9-16. Or, simply go to channel 5 on your TV, then change channels down until you see the DVD Recorder’s logo. Initial Setup will appear the first time you turn on the Recorder. See pages 18-20 to do Initial Setup first.

7 To watch or record the material playing on the other equipment, press MONITOR to put the Recorder in Monitor mode. Press CH+8 or CH-9 to select CAM1 at the Recorder. This is located after your highest TV channel and before your lowest TV channel. Choose CAM1 if you used the connection shown on this page (with the jacks on the front of the Recorder). If you use the IN EXT 1 or IN EXT 2 jacks on the rear of the Recorder instead, choose channel EXT 1 or EXT 2. Choose the chan- nel that matches the jacks to which you connected the other equipment.

Start playing the material by pressing PLAY on the other equip- ment. Press Record I on the front of the DVD Recorder to start recording. See page 21.

DVDR 80

UP

GUIDE

T

R

I

F

G

L

H

E

T

 

DOWN

OPEN

S-VIDEO

VIDEO

 

 

 

 

L AUDIO R

DV IN

 

 

 

CAM 1

CAM 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DV S-VIDEO VIDEO AUDIO

LEFT RIGHT

Helpful Hints

•Use the DV IN CAM 2 jack to connect the Recorder to a Personal Computer that has a Digital Video output.The PC must have an IEEE 1394 Firewire connector. Limited PC applications may be supported. You also can use this jack to connect the Recorder to Digital Video or Hi-8 camcorders. If you use the DV IN CAM 2 jack, choose CAM 2 at the Recorder in Monitor mode to see the material playing on other equip- ment.

•Most prerecorded videotapes and DVDs are copy protected. If you try to copy them, the Recorder display may show “COPY PROTECT.”

•If the Recorder’s display shows “NO SIGNAL,” adjust the track- ing or play the tape at the VCR/Camcorder.

•Do not connect a Progressive Scan video source (such as a DVD Player) to the IN EXT 1 COMPONENT VIDEO jacks.The Recorder cannot receive Progressive Scan video.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents DVDR80 Remember, to get the most from your Philips prod Dear Philips product ownerCard within 10 days. So please mail It to us right now For Customer UseContents Safety Information Example of Antenna Grounding per National Electrical Code Safety Information cont’dIntroduction Discs for Recording and Playing Playable DiscsDiscs Unsuitable for Recording or Playing Discs for Playing OnlyGeneral Information Determining the best possible connection HookupsBefore you begin RememberHookups cont’d Connecting to a TV Only TV has only an Antenna In jackConnecting to a TV and a Cable Box or Satellite Receiver Connecting to a TV Only TV has Component Video In Jacks Connecting to a TV Only TV has an S-Video In Jack Connecting to a TV Only TV has a yellow Cvbs Video In jack Connecting to a TV A Stereo with red/white Audio In jacks Stereo DV S-VIDEO Video Audio Left Right Instructions continue on the next Initial SetupHelpful Hint Initial Setup cont’dPress OK to continue Guide Plus+ System SetupPress Standby y to turn off the Recorder later. Leave the Cable Box turned onPress Monitor to see TV channels through the Recorder Quick RecordingQuick Disc Play To select an item, then press OK. Continue until you set upPress OPEN/CLOSE a again to close the tray Play may start automatically. If notPress Disc Menu during Disc play Title/Disc menusChapter/Track Selection Remote Control TV Volume +/- Buttons Play Mode ButtonDisc Manager Button Standby y ButtonFront Panel Rear Panel Menu Bar 98 symbols in the Menu Bar mean more items are availableMenu Bars On-screen Symbols On-screen Symbols, Status BoxStatus Box Disc status iconsTuner Information box Timer Information boxInformation Boxes Index Picture Screen Title Settings MenuTitles Disc BarPress System MENU. Press to select ClockPress 9CH- repeatedly to select Press 9CH- repeatedly to select Time/Date, then pressChannel Programming To erase a recording, see Erase this title details on One-Touch RecordingPress OK to start Disc play at the Title you selected Title or erase the chosen Title from the DiscErase this title Press to return to the Index Picture Screen if necessaryRecord One Channel/Watch Another Append recordingMode Picture quality Recording time per Disc Record SettingsChapter Markers Recordings and the maximum recording time for a DiscEditing Disc Information Screen Press FSS $ to remove the menu if necessary EditingThis option is not always available Finalize Disc Add current disc Disc ManagerRemove disc Press Play to close the disc tray and remove the DiscBrowse discs Disc Manager cont’dFind title SETUPReview Change Channel Display Guide Plus+ System cont’dReview Options Press GUIDE/TVSort ListingsTimer Recording Tips Timer RecordingsPress Timer X to access the Record screen in the Guide Plus+ SystemMessages and Promotions ScheduleSubtitles Audio Language, SubtitlesAudio Language Zoom Zoom, Camera AngleCamera Angle During DVD play, press the Green Angle Button to SelectSound Sound, Still PictureStill Picture Press System Menu to remove the Menu BarPause k on the remote to pause the picture Slow MotionSearching Time Search Time Search, ScanScan Press the Number buttons to enter the time at which youRepeat A-B Repeat, Repeat A-BRepeat Change Code Access ControlTwice.This will set your code for the first time Press System Menu to remove the menuLocking or Unlocking Specific Discs Child LockParental Level Access Control cont’dChange Country Enter the four-digit code to play the DiscStatus boxes. See See the Status boxes. Choose Off if you do not want to seePicture Settings Analog Output Analog Output, Digital OutputDigital Output Press 9CH- repeatedly to select G, then pressSAP Language SettingsRemote Control Used Night ModePlayback Control Auto Resume, Playback ControlAuto Resume Glossary Helpful Hints Helpful Hints contd Specifications Diagnostic Test, SpecificationsDiagnostic Test Renewed Component video Information Index24-25 Video cvbs
Top Page Image Contents