Philips VRX362AT warranty Turning on Your VCR, Guage, 1Turn on the TV

Page 11

Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected correctly.

●Follow the steps on this page only when you plug the VCR power cord into the wall outlet for the first time.

●You may not be able to program channels at step 5 if you are using a Cable Box.

1

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR.

2

Press the VCR button, then the POWER button. The VCR light and the PWR. (power) light will appear on the display panel and the language select display screen shown below will appear. (If the display does not appear, check your hookups, then follow the steps on page 12 to program channels and page 19 to select a lan-

guage.)

TO SELECT PUSH NO. SHOWN

1

ENGLISH

ON

2

ESPAÑOL

 

MAKE SELECTION OR

PUSH MENU TO CONTINUE

3

Press the Number 1 button to select English on-screen dis- plays. ON will appear to the right of ENGLISH on-screen. Or, press the Number 2 button for Spanish on-screen displays. SI will appear to the right of ESPAÑOL on-screen.

Turning on Your VCR 11

1Turn on the TV.

2

 

 

 

 

 

 

3

 

 

VCR

TV

CABLE

 

POWER

 

/DSS

 

 

 

 

 

1

 

2

3

VCR/TV

5

 

4

 

5

6

 

 

 

 

 

 

CHANNEL

 

7

 

8

9

 

VCR PLUS+

 

 

 

 

 

/ENTER

 

 

 

 

 

 

 

 

0

+100

 

 

 

SPEED

TIME SEARCH

MUTE

VOLUME

 

 

 

 

PLAY

 

 

–

REW

 

F.FWD +

 

 

 

 

STOP

 

 

4

REC/OTR

MEMORY

SLOW

PAUSE/STILL

 

MENU

 

STATUS/EXIT

CLEAR

EJECT

 

4

Press the MENU button. The channel program display shown below will appear. The display will disappear after about 60 sec- onds if you do not press any buttons.

CONNECT ANTENNA OR CABLE

TO VCR

THEN . . .

PUSH CH UP KEY

OR . . .

FOR PLAY ONLY – PUSH STOP

5

Press the CHANNEL (Up) button to begin automatic channel programming. AUTO SET PROCEEDING PLEASE WAIT will appear on-screen. The VCR will place all of the chan- nels you receive into its memory, so when you scan through chan- nels using the CHANNEL (Up/Down) buttons, you’ll only scan through channels that you receive. When all channels are pro- grammed, CHANNELS ARE SET will appear on-screen briefly. Then the TV will go to the lowest channel programmed.

Helpful Hints

•To skip this feature and play a tape immediately, insert a tape with its record tab removed. Or, to skip step 3, press the MENU button. All on- screen displays will be in English. To skip step 5, press the STOP button. Channels will not be programmed, and CHANNELS NOT SET will appear on-screen.

•If you try to program channels when there is no antenna or cable connected to the VCR, programming will appear to take place, but even- tually a NO TV SIGNALS message will appear on-screen. Connect an antenna or cable to the VCR’s ANT(enna) IN Jack and try again. You may need to follow the steps on page 12.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Video Cassette Recorder VRX362AT TM For Customer Use Dear Philips Magnavox product ownerUse FeaturesSafety Precautions IntroductionTable of Contents Remove the battery compartment lid on the bottom Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable BoxPlug in the TV and the VCR Hookups Without a Cable Box cont’dWatching TV With the VCR Off Timer RecordingsHookups With a Cable Box Recording/Viewing Any ChannelPlaying a Tape Connect a Cable signal to the VCR’s ANTenna in JackHookups With a Cable Box cont’d Recording One Channel/Watching AnotherHookups With a Stereo TV 1Turn on the TV Turning on Your VCRGuage Press the VCR button Press the Number 3 button to select Tuner SET UPChannel Memory Programming ChannelsUse the Number buttons to enter the channel number Adding/Deleting ChannelsReviewing Programmed Channels Press the Number 2 button to select SET Manual Clock Setting the ClockManual Clock Setting Press the Number 4 button to select SET ClockCorrect number Enter a 0 before a single digit numberQuestion mark ? to appear on-screen Bring up the main menu display Setting the Clock cont’dAutomatic Clock Setting Press the VCR button, then press the Menu button toPress the Number 4 button to select SET Time Zone Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 4 button to select Language Press the Number 2 button to select VCR SET UPLanguage Selection Language SelectionPress and release the Mute button Find your2TV code Find the brand of your Cable Box or Satellite System on 2FindPlay Button Remote Control ButtonsRemote Control Buttons cont’d Pressed Press the Number 2 button to select on Screen ModeOn-Screen Status Displays To choose the status display mode, follow the steps belowVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape PlayingRecording Press the VCR button on the remote controlPress the Stop button to stop the recording Start a recording seeDoes not appear, press the VCR/TV button once Channels are programmedWith the Tape Speed button Intact and the tape is long enough to record the programsScreen Timer RecordingDaily Recording MenuEnter the recording’s stop time Timer Recording cont’dTape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM See page 50 for more hints Checking or Cancelling Timer RecordingsMenu button Press the Number 1 button to select Program Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Press the Number 5 button to select VCR PLUS+ REF. MAP Press the VCR button, then press the Menu buttonOnce Panel of the VCR. If it does not, press the VCR/TV buttonTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemoryViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monitor MTS Broadcast Stereo SystemUnderstanding On-Screen Displays Specifically…MTS Broadcast Stereo System cont’d Please see additional notes Hi-Fi Stereo Sound SystemPress the Number 3 button to select Audio OUT Press the STATUS/EXIT button to exit Hi-Fi Stereo Sound System cont’dHelpful Hints Helpful Hints cont’d Cable Box Output Channel Channel 3 or GlossarySpecifications Renewed Index Supplied Accessories
Top Page Image Contents