Philips VRX362AT warranty Hookups Without a Cable Box cont’d, Plug in the TV and the VCR

Page 7

Hookups Without a Cable Box (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

	AUDIO		ANT
	AUDIO		IN
		L	IN
		L
	OUT	IN
		R
	VIDEO		OUT
	VIDEO
	OUT	IN CH3 CH4

AUDIO		ANT
AUDIO		IN
	L
OUT	IN
	R
VIDEO		OUT
OUT	IN CH3	CH4

	ANTENNA IN Jack
	(on back of TV)
RF coaxial cable	example only
RF coaxial cable

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. To operate your VCR with your TV, set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 3.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

	AUDIO		ANT
	AUDIO		IN
		L	IN
		L
	OUT	IN
		R
	VIDEO		OUT
	VIDEO
	OUT	IN CH3 CH4

AUDIO		ANT
AUDIO		IN
	L
OUT	IN
	R
VIDEO		OUT
OUT	IN CH3	CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Contents Video Cassette Recorder VRX362AT TM For Customer Use Dear Philips Magnavox product ownerUse FeaturesSafety Precautions Introduction Table of Contents Remove the battery compartment lid on the bottom Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable BoxPlug in the TV and the VCR Hookups Without a Cable Box cont’dWatching TV With the VCR Off Timer RecordingsHookups With a Cable Box Recording/Viewing Any ChannelPlaying a Tape Connect a Cable signal to the VCR’s ANTenna in JackHookups With a Cable Box cont’d Recording One Channel/Watching AnotherHookups With a Stereo TV Guage Turning on Your VCR1Turn on the TV Press the VCR button Press the Number 3 button to select Tuner SET UPChannel Memory Programming ChannelsReviewing Programmed Channels Adding/Deleting ChannelsUse the Number buttons to enter the channel number Press the Number 2 button to select SET Manual Clock Setting the ClockManual Clock Setting Press the Number 4 button to select SET ClockQuestion mark ? to appear on-screen Enter a 0 before a single digit numberCorrect number Bring up the main menu display Setting the Clock cont’dAutomatic Clock Setting Press the VCR button, then press the Menu button toPress the Number 4 button to select SET Time Zone Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 4 button to select Language Press the Number 2 button to select VCR SET UPLanguage Selection Language Selection2TV code Find yourPress and release the Mute button Find the brand of your Cable Box or Satellite System on 2FindPlay Button Remote Control ButtonsRemote Control Buttons cont’d Pressed Press the Number 2 button to select on Screen ModeOn-Screen Status Displays To choose the status display mode, follow the steps belowVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape PlayingRecording Press the VCR button on the remote controlPress the Stop button to stop the recording Start a recording seeDoes not appear, press the VCR/TV button once Channels are programmedWith the Tape Speed button Intact and the tape is long enough to record the programsScreen Timer RecordingDaily Recording MenuEnter the recording’s stop time Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Menu button Press the Number 1 button to select Program Checking or Cancelling Timer RecordingsSee page 50 for more hints TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Press the Number 5 button to select VCR PLUS+ REF. MAP Press the VCR button, then press the Menu buttonOnce Panel of the VCR. If it does not, press the VCR/TV buttonTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemoryViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monitor MTS Broadcast Stereo SystemUnderstanding On-Screen Displays Specifically…MTS Broadcast Stereo System cont’d Press the Number 3 button to select Audio OUT Hi-Fi Stereo Sound SystemPlease see additional notes Press the STATUS/EXIT button to exit Hi-Fi Stereo Sound System cont’dHelpful Hints Helpful Hints cont’d Cable Box Output Channel Channel 3 or GlossarySpecifications Renewed Index Supplied Accessories