Philips VRX362AT warranty Time Search

Page 42

42 Time Search

Time Search

Follow the steps below to program the VCR to search forward or backward a specific length of time.

1

Press the VCR button.

2

Press the TIME SEARCH button to bring up the time search display. There must be a tape in the VCR.

TIME SEARCH

0:00

3

2

1

		VCR	TV	CABLE
	POWER	VCR	TV	/DSS
	POWER			/DSS
		2	3	VCR/TV
	1	2	3
	4	5	6
				CHANNEL
	7	8	9
	VCR PLUS+
	/ENTER

0+100

SPEED

TIME SEARCH

MUTE

VOLUME

ENTER SEARCH TIME

3

Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward. For example, for 1 hour, 25 minutes, press Number but- tons 1, 2, 5. Or, for five minutes, press Number buttons 0, 0, 5. (Make an entry within 10 seconds of pressing the TIME SEARCH button. Otherwise, the VCR will exit Time Search mode.)

4

Within 10 seconds, press the F.FWD button or the REW(ind) button to skip forward or backward. The VCR will skip over the specified length of time, then begin playback. (The time counts down on-screen as the searching progresses.)

		PLAY
–	REW			F.FWD +
4		STOP
	REC/OTR	MEMORY	SLOW	PAUSE/STILL
	MENU	STATUS/EXIT	CLEAR	EJECT

Helpful Hints

•If you want to search for more than 59 minutes, you must enter the length of time in hours and minutes. For example, to search forward 70 minutes, press 1,1,0 at step 3.

•You can not enter the TIME SEARCH menu when you are in Recording mode.

•You can remove the Time Search display by pressing the TIME SEARCH button again.

•To cancel the Time Search when the VCR is fast forwarding or rewinding, press the STOP button once or the

TIME SEARCH button twice.

Image 42

Contents Video Cassette Recorder VRX362AT TM Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions UseTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Remove the battery compartment lid on the bottomHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRRecording/Viewing Any Channel Timer RecordingsHookups With a Cable Box Watching TV With the VCR OffRecording One Channel/Watching Another Connect a Cable signal to the VCR’s ANTenna in JackHookups With a Cable Box cont’d Playing a TapeHookups With a Stereo TV Turning on Your VCR Guage1Turn on the TV Programming Channels Press the Number 3 button to select Tuner SET UPChannel Memory Press the VCR buttonAdding/Deleting Channels Reviewing Programmed ChannelsUse the Number buttons to enter the channel number Press the Number 4 button to select SET Clock Setting the ClockManual Clock Setting Press the Number 2 button to select SET Manual ClockEnter a 0 before a single digit number Question mark ? to appear on-screenCorrect number Press the VCR button, then press the Menu button to Setting the Clock cont’dAutomatic Clock Setting Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 4 button to select LanguageFind your 2TV codePress and release the Mute button 2Find Find the brand of your Cable Box or Satellite System onRemote Control Buttons Play ButtonRemote Control Buttons cont’d To choose the status display mode, follow the steps below Press the Number 2 button to select on Screen ModeOn-Screen Status Displays PressedVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tapePress the VCR button on the remote control RecordingStart a recording see Press the Stop button to stop the recordingIntact and the tape is long enough to record the programs Channels are programmedWith the Tape Speed button Does not appear, press the VCR/TV button onceRecording Menu Timer RecordingDaily ScreenTimer Recording cont’d Enter the recording’s stop timeTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings Menu button Press the Number 1 button to select ProgramSee page 50 for more hints Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Press the VCR button, then press the Menu button Press the Number 5 button to select VCR PLUS+ REF. MAPPanel of the VCR. If it does not, press the VCR/TV button OnceTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemorySuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Specifically… MTS Broadcast Stereo SystemUnderstanding On-Screen Displays MonitorMTS Broadcast Stereo System cont’d Hi-Fi Stereo Sound System Press the Number 3 button to select Audio OUTPlease see additional notes Hi-Fi Stereo Sound System cont’d Press the STATUS/EXIT button to exitHelpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories