Philips VRX362AT warranty Timer Recording, Daily, Recording Menu, Screen

Page 32

32 Timer Recording

Follow the steps below to program your VCR to record TV pro- grams while you’re away from home. You can program up to eight timer recordings. For each one, the VCR will turn itself on, record, and turn itself off automatically. Before you begin make sure:

●Channels are programmed.

●The clock is set.

●There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s).

●The VCR is in VCR position. The VCR light will appear on the display panel when the VCR is in VCR position. If the VCR light does not appear, press the VCR/TV button once.

Do each step within 60 seconds of completing the previ- ous step. If you don’t, you may start again at step 1.

1

POWER

VCR

TV

1 2 3

4 5 6

7 8 9

VCR PLUS+
/ENTER
	0	+100
SPEED	TIME SEARCH	MUTE

CABLE /DSS

VCR/TV

CHANNEL

VOLUME

3 2

Press the VCR button, then press the MENU button to

bring up the main menu display.

TO SELECT PUSH NO. SHOWN

1PROGRAM

2VCR SET UP

3TUNER SET UP

4SET CLOCK

TO END PUSH EXIT

2

Press the Number 1 button on the remote control to select

PROGRAM.

TO SELECT PUSH NO. SHOWN

1ONCE

2DAILY

3WEEKLY

4PROGRAM REVIEW

TO END PUSH EXIT

3

Select a once, daily or weekly recording.

●Press the Number 1 button to select ONCE. The VCR will record a TV program on any day you choose, up to 12 months away.

●Press the Number 2 button to select DAILY. The VCR will record every day from Monday to Friday – starting at the same time and for the same length of time.

●Press the Number 3 button to select WEEKLY. The VCR will record on the same day, at the same time, and for the same length of time every week.

DAILY PROGRAM (MON-FRI)

	Daily	PROGRAM -1 2 3 4 5 6 7 8-
	Daily
	Recording
	Menu	SELECT PROGRAM NUMBER
	Screen	SELECT PROGRAM NUMBER
	Screen	TO END PUSH EXIT

		PLAY
	– REW			F.FWD +
		STOP
1	REC/OTR	MEMORY	SLOW	PAUSE/STILL
1	MENU	STATUS/EXIT	CLEAR	EJECT

Helpful Hint

•If you need to make a correction while programming a timer record- ing, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the

correct information.

Image 32

Contents Video Cassette Recorder VRX362AT TM Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction UseTable of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Remove the battery compartment lid on the bottomHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRTimer Recordings Hookups With a Cable BoxRecording/Viewing Any Channel Watching TV With the VCR OffConnect a Cable signal to the VCR’s ANTenna in Jack Hookups With a Cable Box cont’dRecording One Channel/Watching Another Playing a TapeHookups With a Stereo TV 1Turn on the TV Turning on Your VCRGuage Press the Number 3 button to select Tuner SET UP Channel MemoryProgramming Channels Press the VCR buttonUse the Number buttons to enter the channel number Adding/Deleting ChannelsReviewing Programmed Channels Setting the Clock Manual Clock SettingPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual ClockCorrect number Enter a 0 before a single digit numberQuestion mark ? to appear on-screen Setting the Clock cont’d Automatic Clock SettingPress the VCR button, then press the Menu button to Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 2 button to select VCR SET UP Language SelectionLanguage Selection Press the Number 4 button to select LanguagePress and release the Mute button Find your2TV code 2Find Find the brand of your Cable Box or Satellite System onRemote Control Buttons Play ButtonRemote Control Buttons cont’d Press the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below PressedVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tapePress the VCR button on the remote control RecordingStart a recording see Press the Stop button to stop the recordingChannels are programmed With the Tape Speed buttonIntact and the tape is long enough to record the programs Does not appear, press the VCR/TV button onceTimer Recording DailyRecording Menu ScreenTimer Recording cont’d Enter the recording’s stop timeTape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM See page 50 for more hints Checking or Cancelling Timer RecordingsMenu button Press the Number 1 button to select Program Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Press the VCR button, then press the Menu button Press the Number 5 button to select VCR PLUS+ REF. MAPPanel of the VCR. If it does not, press the VCR/TV button OnceTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemorySpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features MTS Broadcast Stereo System Understanding On-Screen DisplaysSpecifically… MonitorMTS Broadcast Stereo System cont’d Please see additional notes Hi-Fi Stereo Sound SystemPress the Number 3 button to select Audio OUT Hi-Fi Stereo Sound System cont’d Press the STATUS/EXIT button to exitHelpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories