Philips VRX362AT warranty Rerecording Tape Duplication

Page 40

40 Rerecording (Tape Duplication)

VCR 1 - Playing VCR

VCR 2 - Recording VCR

AUDIO		ANT	AUDIO		ANT
AUDIO		IN	AUDIO		IN
	L			L
OUT	IN		OUT	IN
	R			R
VIDEO		OUT	VIDEO		OUT
OUT	IN CH3	CH4	OUT	IN CH3	CH4

3. RF coaxial cable

(supplied) from

VCR’s OUT Jack to TV’s ANTENNA IN Jack

1.Audio cables from AUDIO OUT Jacks of VCR 1 to AUDIO IN Jacks of VCR 2

2.Video cable from VIDEO OUT Jack of VCR 1 to VIDEO IN Jack of VCR 2

●Audio and Video cables are not supplied.

The instructions on this page show you how to copy tapes. The illustration uses two VCRs just like yours. Different VCRs may operate differently.

NOTE: Unauthorized recording of copyrighted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws.

1

Make the connections shown above.

2

VCR 1 will play your tape. Insert a prerecorded tape in VCR

1.If the tape does not have a record tab, playback begins. If this happens, press the STOP/EJECT button on VCR 1 once.

3

VCR 2 will record your tape. Insert a blank tape in VCR 2. Make sure the VCR 2 power is on and VCR 2 is in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button once.)

4

Turn the TV on and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on VCR 2 is set to.

5

Point the remote control at VCR 2. Press Number but- tons 0, 0, 1 or 0, 0, 2. (See Helpful Hints at right.)

6

Point the remote control at VCR 2. Use the (Tape) SPEED button to select SP, LP or SLP.

7

Press the PLAY button on VCR 1 and the REC(ord)/OTR button on VCR 2 at the same time.

To stop recording, press the STOP/EJECT button on VCR 1, then press the STOP/EJECT button on VCR 2.

Helpful Hints

•If you use the AUDIO and VIDEO IN Jacks on the back of VCR 2, press Number buttons 0, 0, 1. AV REAR will appear on-screen.

•If you use the AUDIO and VIDEO IN Jacks on the front of VCR 2, press Number buttons 0, 0, 2. AV FRONT will appear on-screen.

Image 40

Contents Video Cassette Recorder VRX362AT TM Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction UseTable of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Remove the battery compartment lid on the bottomHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Plug in the TV and the VCRTimer Recordings Hookups With a Cable BoxRecording/Viewing Any Channel Watching TV With the VCR OffConnect a Cable signal to the VCR’s ANTenna in Jack Hookups With a Cable Box cont’dRecording One Channel/Watching Another Playing a TapeHookups With a Stereo TV Guage Turning on Your VCR1Turn on the TV Press the Number 3 button to select Tuner SET UP Channel MemoryProgramming Channels Press the VCR buttonReviewing Programmed Channels Adding/Deleting ChannelsUse the Number buttons to enter the channel number Setting the Clock Manual Clock SettingPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual ClockQuestion mark ? to appear on-screen Enter a 0 before a single digit numberCorrect number Setting the Clock cont’d Automatic Clock SettingPress the VCR button, then press the Menu button to Bring up the main menu displayTime Zone Press the Number 4 button to select SET Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 2 button to select VCR SET UP Language SelectionLanguage Selection Press the Number 4 button to select Language2TV code Find yourPress and release the Mute button 2Find Find the brand of your Cable Box or Satellite System onRemote Control Buttons Play ButtonRemote Control Buttons cont’d Press the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below PressedVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tapePress the VCR button on the remote control RecordingStart a recording see Press the Stop button to stop the recordingChannels are programmed With the Tape Speed buttonIntact and the tape is long enough to record the programs Does not appear, press the VCR/TV button onceTimer Recording DailyRecording Menu ScreenTimer Recording cont’d Enter the recording’s stop timePress the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Menu button Press the Number 1 button to select Program Checking or Cancelling Timer RecordingsSee page 50 for more hints TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Press the VCR button, then press the Menu button Press the Number 5 button to select VCR PLUS+ REF. MAPPanel of the VCR. If it does not, press the VCR/TV button OnceTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemorySpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features MTS Broadcast Stereo System Understanding On-Screen DisplaysSpecifically… MonitorMTS Broadcast Stereo System cont’d Press the Number 3 button to select Audio OUT Hi-Fi Stereo Sound SystemPlease see additional notes Hi-Fi Stereo Sound System cont’d Press the STATUS/EXIT button to exitHelpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories