Philips VRX362AT warranty Timer Recording With the VCR Plus+ Programming System cont’d

Page 39

Timer Recording With the VCR Plus+ Programming System (cont’d) 39

5

Press the Number 1 button to record in SP speed, the Number 2 button to record in LP speed, or the Number 3 button to record in SLP speed. Your selection will appear to the right of REC SPEED on-screen, although SP=1 LP=2 SLP=3 will continue to flash. For details about tape speed, see pages 34 and 52. You cannot use the (Tape) SPEED button at this time.

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

9

TIME ON

10:30 PM

TIME OFF

11:30 PM

REC SPEED

SLP

SP=1 LP=2

SLP=3

START DATE

10/10/97

 

FRI.

TO END PUSH EXIT

6

Press the STATUS/EXIT button. PROGRAM WAS COM-

PLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen. After three seconds, the on-screen display will disappear.

7

Press the POWER button to turn off the VCR power. The Timer light will appear. The Timer light will flash if there is not a tape in the VCR.

If the timer recording will take place several hours or days from now, you may use the VCR until time for the recording. Just turn off the VCR a few minutes before the recording starts.

The VCR must be turned off for a timer recording to take place. If you forget to turn off the VCR, PLEASE TURN OFF VCR FOR TIMER RECORDING flashes on your TV screen two minutes before a timer recording starts. You can remove the mes- sage by pressing the CLEAR button.

The VCR must be off for a

timer recording to take

place! Make sure there is a

tape in the VCR.

7

 

 

 

 

5

 

VCR

TV

CABLE

POWER

/DSS

 

 

 

2

3

VCR/TV

1

 

 

4

5

6

 

 

 

 

 

CHANNEL

 

7

8

9

 

 

VCR PLUS+

 

 

 

 

/ENTER

 

 

 

0+100

SPEED

TIME SEARCH

MUTE

VOLUME

 

PLAY

 

– REW

 

F.FWD +

 

STOP

 

REC/OTR

MEMORY

SLOW

PAUSE/STILL

MENU

STATUS/EXIT

CLEAR

EJECT

6

Helpful Hints

•To exit the VCR Plus+ programming system at any time, press the STA- TUS/EXIT button. The display will disappear from the TV screen.

•If the preset time for a timer recording comes up during an OTR, the OTR has priority.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If the power fails for more than one minute, programmed timer record- ings may be lost. Reset the clock before re-programming the timer recordings.

•If you are using a Cable Box, timer recordings are programmed differ- ently. See page eight for details.

See page 50 for more hints.

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Video Cassette Recorder VRX362AT TM For Customer Use Dear Philips Magnavox product ownerUse FeaturesSafety Precautions IntroductionTable of Contents Remove the battery compartment lid on the bottom Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable BoxPlug in the TV and the VCR Hookups Without a Cable Box cont’dWatching TV With the VCR Off Timer RecordingsHookups With a Cable Box Recording/Viewing Any ChannelPlaying a Tape Connect a Cable signal to the VCR’s ANTenna in JackHookups With a Cable Box cont’d Recording One Channel/Watching AnotherHookups With a Stereo TV Turning on Your VCR Guage1Turn on the TV Press the VCR button Press the Number 3 button to select Tuner SET UPChannel Memory Programming ChannelsAdding/Deleting Channels Reviewing Programmed ChannelsUse the Number buttons to enter the channel number Press the Number 2 button to select SET Manual Clock Setting the ClockManual Clock Setting Press the Number 4 button to select SET ClockEnter a 0 before a single digit number Question mark ? to appear on-screenCorrect number Bring up the main menu display Setting the Clock cont’dAutomatic Clock Setting Press the VCR button, then press the Menu button toPress the Number 4 button to select SET Time Zone Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionPress the Number 4 button to select Language Press the Number 2 button to select VCR SET UPLanguage Selection Language SelectionFind your 2TV codePress and release the Mute button Find the brand of your Cable Box or Satellite System on 2FindPlay Button Remote Control ButtonsRemote Control Buttons cont’d Pressed Press the Number 2 button to select on Screen ModeOn-Screen Status Displays To choose the status display mode, follow the steps belowVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape PlayingRecording Press the VCR button on the remote controlPress the Stop button to stop the recording Start a recording seeDoes not appear, press the VCR/TV button once Channels are programmedWith the Tape Speed button Intact and the tape is long enough to record the programsScreen Timer RecordingDaily Recording MenuEnter the recording’s stop time Timer Recording cont’dTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings Menu button Press the Number 1 button to select ProgramSee page 50 for more hints Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Press the Number 5 button to select VCR PLUS+ REF. MAP Press the VCR button, then press the Menu buttonOnce Panel of the VCR. If it does not, press the VCR/TV buttonTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemoryViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monitor MTS Broadcast Stereo SystemUnderstanding On-Screen Displays Specifically…MTS Broadcast Stereo System cont’d Hi-Fi Stereo Sound System Press the Number 3 button to select Audio OUTPlease see additional notes Press the STATUS/EXIT button to exit Hi-Fi Stereo Sound System cont’dHelpful Hints Helpful Hints cont’d Cable Box Output Channel Channel 3 or GlossarySpecifications Renewed Index Supplied Accessories
Top Page Image Contents