Philips VRX362AT warranty Press the VCR button, then press the Menu button

Page 37

Setting Up the VCR Plus+ Programming System (cont’d) 37

2

2 Examine the lists on page 36.

Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps.

●Make each entry within 60 seconds of the previous entry.

3

Press the VCR button, then press the MENU button.

4

POWER

VCR

TV

5	1	2	3
5	4	5	6
	7	8	9
	VCR PLUS+
	/ENTER
		0	+100
	SPEED	TIME SEARCH	MUTE

CABLE /DSS

VCR/TV

CHANNEL

VOLUME

4 6

Press the Number 2 button to select VCR SET UP.

TO SELECT PUSH NO. SHOWN

1 REPEAT PLAY

OFF

2 ON SCREEN MODE

	PLAY
– REW			F.FWD +
	STOP
REC/OTR	MEMORY	SLOW	PAUSE/STILL

3	AUDIO OUT
4	LANGUAGE
5	VCR PLUS+ REF. MAP

TO END PUSH EXIT

5

Press the Number 5 button to select VCR PLUS+ REF. MAP.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1	– – – – –>	1
2		2

TO SELECT CH PUSH CH UP/

DOWN THEN ENTER CH NO.

TO END PUSH EXIT

3

7

MENU

STATUS/EXIT

CLEAR

EJECT

6

Look at the lists you filled in on page 36. For stations whose

VCR Plus+ and Cable/TV channels do not match, press the CHANNEL (Up/Down) buttons until the arrow is beside the VCR Plus+ channel you need. Then, press the Number buttons to enter the corresponding Cable/TV channel from your list. (Enter a “0” before single-digit chan- nels.) Continue this process until you have entered all the stations on your list.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1– – – – –> 23

22

TO SELECT CH PUSH CH UP/

DOWN THEN ENTER CH NO.

TO END PUSH EXIT

7

Press the STATUS/EXIT button to exit.

Helpful Hints

•To correct a Cable/TV channel num- ber, repeat the steps on this page.

•To clear a Cable/TV channel number, repeat steps 3-5 on this page. Then, press the CHANNEL (Up/Down) but- tons to select it. Then press the CLEAR button. Press the STATUS/EXIT button to exit.

•Always enter a “0” before single- digit channels.

•To select line input for the Cable/TV channel, press 0,0. AUX will appear on-screen.

•When you receive the VCR from the factory, all the VCR Plus+ channel numbers and Cable/TV channel numbers are the same.

Image 37

Contents Video Cassette Recorder VRX362AT TM For Customer Use Dear Philips Magnavox product ownerSafety Precautions FeaturesIntroduction UseTable of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Remove the battery compartment lid on the bottomDisconnect the antenna or cable from your TV Hookups Without a Cable BoxPlug in the TV and the VCR Hookups Without a Cable Box cont’dHookups With a Cable Box Timer RecordingsRecording/Viewing Any Channel Watching TV With the VCR OffHookups With a Cable Box cont’d Connect a Cable signal to the VCR’s ANTenna in JackRecording One Channel/Watching Another Playing a TapeHookups With a Stereo TV Guage Turning on Your VCR1Turn on the TV Channel Memory Press the Number 3 button to select Tuner SET UPProgramming Channels Press the VCR buttonReviewing Programmed Channels Adding/Deleting ChannelsUse the Number buttons to enter the channel number Manual Clock Setting Setting the ClockPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual ClockQuestion mark ? to appear on-screen Enter a 0 before a single digit numberCorrect number Automatic Clock Setting Setting the Clock cont’dPress the VCR button, then press the Menu button to Bring up the main menu displayPress the Number 4 button to select SET Time Zone Time ZoneDaylight-Saving Time Selection Daylight-Saving Time SelectionLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 4 button to select Language2TV code Find yourPress and release the Mute button Find the brand of your Cable Box or Satellite System on 2FindPlay Button Remote Control ButtonsRemote Control Buttons cont’d On-Screen Status Displays Press the Number 2 button to select on Screen ModeTo choose the status display mode, follow the steps below PressedVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape PlayingRecording Press the VCR button on the remote controlPress the Stop button to stop the recording Start a recording seeWith the Tape Speed button Channels are programmedIntact and the tape is long enough to record the programs Does not appear, press the VCR/TV button onceDaily Timer RecordingRecording Menu ScreenEnter the recording’s stop time Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Menu button Press the Number 1 button to select Program Checking or Cancelling Timer RecordingsSee page 50 for more hints TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Press the Number 5 button to select VCR PLUS+ REF. MAP Press the VCR button, then press the Menu buttonOnce Panel of the VCR. If it does not, press the VCR/TV buttonTimer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat PlaybackTime Search Time SearchReal Time Counter Memory Real Time Counter MemoryForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays MTS Broadcast Stereo SystemSpecifically… MonitorMTS Broadcast Stereo System cont’d Press the Number 3 button to select Audio OUT Hi-Fi Stereo Sound SystemPlease see additional notes Press the STATUS/EXIT button to exit Hi-Fi Stereo Sound System cont’dHelpful Hints Helpful Hints cont’d Cable Box Output Channel Channel 3 or GlossarySpecifications Renewed Index Supplied Accessories