Philips VRA211AT owner manual Hookups With a Stereo TV

Page 10

10 Hookups With a Stereo TV

			antenna or
			1 ANT(enna)cable to
		ANT	IN Jack
		IN
AUDIO
OUT	IN	OUT
		OUT
VIDEO		CH3 CH4
VIDEO
VIDEO (yellow) and		2
AUDIO (white) OUT Jacks		2	Video Cable
AUDIO (white) OUT Jacks

3 Audio Cable

●Audio and Video cables are not supplied.

1

Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.

2

Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV.

3

Connect an audio cable to the white AUDIO OUT Jack on the back of the VCR. Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV.

(If your TV has Right and Left AUDIO IN Jacks, you must use a “Y” splitter audio cable as illustrated to deliver audio to the TV’s right and left channels.)

4

Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owner’s manual for details.

Audio and Video IN Jacks on TV

Helpful Hint

•This hookup will not give you stereo sound. To get stereo sound, use the connections on pages six - seven and select the channel to be viewed at the TV (with the VCR turned off).

Image 10

Contents VRA211AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRRecording/Viewing Any Channel Cable Signal RF coaxialConnections RF coaxial Cable TV’s ANTENNAJackRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV 2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appearPress the VCR button Automatic Channel SetupPress the Menu button Automatic Channel Setup cont’d Adding/Deleting ChannelsPress the VCR button Press the Menu button Reviewing Memorized ChannelsPress the STATUS/EXIT button once or twice to exit Setting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR If the VCR light appears on the display panel, go to . If RecordingInsert a tape with its record tab intact in the VCR VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Press the VCR button, then press the Menu button Timer RecordingDo each step within 60 seconds of the previous step DailyTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Timer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication RF coaxial cableRepeat Play Press the F.FWD/B button so that on appears besideReal-Time Counter Memory Button to reset the real-time counter to zeroWhile the status display is on-screen, press the Clear Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel 03 orHelpful Hints Helpful Hints cont’d Specifications Limited Warranty Model # Serial #Index Page Supplied Accessories