Philips VRA211AT owner manual Checking or Cancelling Timer Recordings

Page 31

Timer Recording (cont’d) 31

Checking or Cancelling Timer Recordings

1

 

With the VCR on and in VCR position (the VCR light will appear

1

on the display panel), press the VCR button, then press the

MENU button.

2

 

Press the PLAY/o button or the STOP/p button to select

 

PROGRAM, then press the F.FWD/B button.

 

2-3

POWER

VCR/TV

EJECT

VCR

TV

 

 

PLAY

 

REW

 

F.FWD

 

STOP

 

MENU

STATUS/EXIT

CLEAR

4

5

3

Press the PLAY/o button or the STOP/p button to select

1 2 3

4 5 6

7 8 9

CH

PROGRAM REVIEW, then press the F.FWD/B button.

The timer recording information for the program in the lowest

numbered slot will appear on-screen. If no timer recordings are

set, nothing will happen when you press the F.FWD/B button.

ALT. CH

0VOL

SPEEDPAUSE/STILL

REC/OTR MEMORY

MUTE

4

Press the F.FWD/B button repeatedly to review all pro- grammed timer recordings. If you don’t press the F.FWD/B button within 10 seconds, the VCR will automatically display infor- mation about the next programmed timer recording. This will continue until all timer recordings have been displayed. Then the menu will disappear.

5

To cancel the timer recording displayed, press the CLEAR button. Either the display will disappear or information about other timer recordings will appear. If you do not press any other buttons, the display will disappear after all timer recordings have been displayed.

6

Repeat steps 1 - 4 to make sure you have cleared the cor- rect timer recording.

Helpful Hints

•CLASH may flash on-screen when you finish setting a timer recording. This means that the timer recording you just programmed and another timer record- ing overlap. The current timer recording will not take place. You may choose to cancel the overlapping timer recording.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If the power fails for more than one minute, programmed timer recordings will be lost. If this occurs, repeat the steps on pages 11 and 15 before reset- ting the timer recordings.

•If the preset time for a timer recording comes up during an OTR, the OTR has priority. A message will remind you when the timer recording was scheduled to begin. You may let the OTR continue; the timer recording will not take place. Or, stop the OTR and turn off the VCR immediately. The timer recording will take place if you turn off the VCR before the timer recording’s scheduled

start time.

See page 38 for more hints.

Page 30 Page 32
Image 31
Page 30 Page 32
Contents VRA211AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialSafety Precautions FeaturesIntroduction Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemPlug in the TV and the VCR CH3 CH4RF coaxial Cable TV’s ANTENNAJack Cable Signal RF coaxialConnections Recording/Viewing Any ChannelCable Box/DBS Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Recording One Channel/Watching AnotherHookups With a Stereo TV Press the Menu button. The display shown below will appear Press the VCR button, then press the Power buttonTurning on Your VCR 2Turn on the TVPress the VCR button Automatic Channel SetupPress the Menu button Adding/Deleting Channels Automatic Channel Setup cont’dPress the VCR button Press the Menu button Reviewing Memorized ChannelsPress the STATUS/EXIT button once or twice to exit Enter a 0 before a single-digit number Setting the ClockDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR VCR light does not appear, press the VCR/TV button once RecordingInsert a tape with its record tab intact in the VCR If the VCR light appears on the display panel, go to . IfVCR light will disappear from the VCR’s display panel Recording One Channel/Watching AnotherOne-Touch Recording Daily Timer Recording Do each step within 60 seconds of the previous step Press the VCR button, then press the Menu buttonTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Timer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayReal-Time Counter Memory Button to reset the real-time counter to zeroWhile the status display is on-screen, press the Clear Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Cable Box/DBS Output Channel 03 or GlossaryHelpful Hints Helpful Hints cont’d Specifications Model # Serial # Limited WarrantyIndex Page Supplied Accessories
Top Page Image Contents