Philips VRA211AT On-Screen Status Displays, Status Display example only, If you select Status OFF

Page 20

20 On-Screen Status Displays

A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below.

If you select STATUS ON, then select COUNTER ONLY ON:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. After five seconds, only the counter will remain on-screen. You must press the STA- TUS/EXIT button to remove it. Portions of the status display also

may appear when you press other function buttons.

If you select STATUS ON, then select COUNTER ONLY OFF:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the sta-

tus display also may appear when you press other function but- tons.

If you select STATUS OFF:

●The status display will not appear when you press function but- tons. You must press the STATUS/EXIT button to see the status display.

1

Press the VCR button, then press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select ON SCREEN MODE, then press the F.FWD/B button.

4

Press the PLAY/o button or the STOP/p button to select STATUS, then press the F.FWD/B button so that OFF (or ON) appears beside STATUS.

SELECT op CHOOSE B

→ STATUS	[ON]
COUNTER ONLY	[OFF]
TO END PUSH EXIT

Status Display (example only)

Current status

of tape		Time


STOP		12:00 AM
		CH10
SLP		M 1:23:45

Channel

Tape Counter

Speed and

Counter

Memory

5

If you set STATUS to OFF, go to step 6. If you set STA- TUS to ON, press the PLAY/o button or the STOP/p button to select COUNTER ONLY, then press the F.FWD/B button so that OFF (or ON) appears beside it.

6

Press the STATUS/EXIT button.

Helpful Hint

•You may not access a status display when viewing a still picture or when the F.FWD/B or REW(ind)/s but- ton is pressed during playback.

Image 20

Contents VRA211AT Dear Philips Magnavox product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoIntroduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRCable Signal RF coaxial ConnectionsRecording/Viewing Any Channel RF coaxial Cable TV’s ANTENNAJackCable Signal Connect a Cable signal to the VCR’s ANTenna in JackRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Press the VCR button, then press the Power button Turning on Your VCR2Turn on the TV Press the Menu button. The display shown below will appearPress the Menu button Automatic Channel SetupPress the VCR button Automatic Channel Setup cont’d Adding/Deleting ChannelsPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsPress the VCR button Press the Menu button Setting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Recording Insert a tape with its record tab intact in the VCRIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Timer Recording Do each step within 60 seconds of the previous stepPress the VCR button, then press the Menu button DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Program REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsTimer recording information for the program in the lowest Rerecording Tape Duplication RF coaxial cableRepeat Play Press the F.FWD/B button so that on appears besideWhile the status display is on-screen, press the Clear Button to reset the real-time counter to zeroReal-Time Counter Memory Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel 03 orHelpful Hints Helpful Hints cont’d Specifications Limited Warranty Model # Serial #Index Page Supplied Accessories