Philips VRA211AT Reviewing Memorized Channels, Press the VCR button Press the Menu button

Page 14

14 Automatic Channel Setup (cont’d)

Reviewing Memorized Channels

1

Press the VCR button.

2

Press the MENU button.

SELECT op CHOOSE B

→PROGRAM VCR SET UP TUNER SET UP SET CLOCK

1

3-4

POWER VCR/TV EJECT

VCR

TV

PLAY

REWF.FWD

STOP

TO END PUSH EXIT

3

Press the PLAY/o button or the STOP/p button to select TUNER SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B

2

MENU	STATUS/EXIT

1 2 3

4 5 6

7 8 9

ALT. CH

0

SPEEDPAUSE/STILL

CLEAR

5

CH

VOL

→AUTO PROGRAMMING ADD/DELETE CH

CH MEMORY REVIEW

TO END PUSH EXIT

4

Press the PLAY/o button or the STOP/p button to select CH MEMORY REVIEW, then press the F.FWD/B button. A list of programmed channels will appear on-screen.

●If all the programmed channels don’t fit on the screen, press the F.FWD/B button to see the remaining channels. Then press the REW(ind)/s button to return to the first screen of channels.

●If you do not press any buttons within 10 seconds, you will either go to the next screen of channels or you will return to the previous menu.

5

Press the STATUS/EXIT button once or twice to exit.

REC/OTR MEMORY

MUTE

Image 14

Contents VRA211AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoIntroduction FeaturesSafety Precautions Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRRecording/Viewing Any Channel Cable Signal RF coaxialConnections RF coaxial Cable TV’s ANTENNAJackRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV 2Turn on the TV Press the VCR button, then press the Power button Turning on Your VCR Press the Menu button. The display shown below will appearPress the Menu button Automatic Channel SetupPress the VCR button Automatic Channel Setup cont’d Adding/Deleting ChannelsPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsPress the VCR button Press the Menu button Setting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape If the VCR light appears on the display panel, go to . If RecordingInsert a tape with its record tab intact in the VCR VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Press the VCR button, then press the Menu button Timer RecordingDo each step within 60 seconds of the previous step DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Program REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsTimer recording information for the program in the lowest Rerecording Tape Duplication RF coaxial cableRepeat Play Press the F.FWD/B button so that on appears besideWhile the status display is on-screen, press the Clear Button to reset the real-time counter to zeroReal-Time Counter Memory Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel 03 orHelpful Hints Helpful Hints cont’d Specifications Limited Warranty Model # Serial #Index Page Supplied Accessories