Philips VRA211AT owner manual Playing, Read and follow the steps below to play a tape

Page 24

24 Playing

Read and follow the steps below to play a tape.

1

Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to.

1Turn on the TV.

2Insert a tape in the VCR.

2

Insert a tape in the VCR. The PWR., VCR, and Cassette-Inside lights will appear on the display panel. If the tape’s record tab has been removed, playback will start automatically.

3

If playback does not start automatically, press the VCR button, then press the PLAY/o button.

4

Press the STOP/p button to stop playback.

	POWER
	VCR
3	REW
5	MENU

1

4

7

VCR/TV EJECT

TV

PLAY

	F.FWD
STOP
STATUS/EXIT	CLEAR

2	3
5	6	CH
5	6
8	9
	ALT. CH
0		VOL
0

6

4

5

Press the REW(ind)/{ button to rewind the tape.

6

Press the EJECT button to remove the tape.

SPEEDPAUSE/STILL

REC/OTR MEMORY

MUTE

Helpful Hints

•If the tape you want to play is already in the VCR, make sure the VCR power is on and the VCR is in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button.) Press the VCR button, then press the PLAY/o button.

•Other playback options and fea- tures are on pages 33 - 36.

Image 24

Contents VRA211AT Dear Philips Magnavox product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRCable Signal RF coaxial ConnectionsRecording/Viewing Any Channel RF coaxial Cable TV’s ANTENNAJackCable Signal Connect a Cable signal to the VCR’s ANTenna in JackRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Press the VCR button, then press the Power button Turning on Your VCR2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR buttonPress the Menu button Automatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the VCR button Press the Menu buttonPress the STATUS/EXIT button once or twice to exit Setting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape in the VCR Recording Insert a tape with its record tab intact in the VCRIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Timer Recording Do each step within 60 seconds of the previous stepPress the VCR button, then press the Menu button DailyTimer Recording cont’d Timer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication RF coaxial cableRepeat Play Press the F.FWD/B button so that on appears besideButton to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on-screen, press the Clear Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel 03 orHelpful Hints Helpful Hints cont’d Specifications Limited Warranty Model # Serial #Index Page Supplied Accessories