Philips VRA211AT owner manual Repeat Play, Press the F.FWD/B button so that on appears beside

Page 33

Follow the steps below to make the VCR play a tape over and over.

Repeat Play 33

1

Press the VCR button.

2

Press the MENU button.

SELECT op CHOOSE B

→PROGRAM VCR SET UP TUNER SET UP SET CLOCK

TO END PUSH EXIT

3

1

4

2

POWER

VCR

REW

MENU

1

4

7

VCR/TV EJECT

TV

PLAY

	F.FWD
STOP
STATUS/EXIT	CLEAR

2	3
5	6	CH
5	6
8	9
	ALT. CH
0		VOL
0

3

5

6

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B
→ REPEAT PLAY	OFF
ON SCREEN MODE
LANGUAGE
BLUE BACKGROUND	ON
TO END PUSH EXIT

4

Press the PLAY/o button or the STOP/p button to select

REPEAT PLAY.

5

Press the F.FWD/B button so that ON appears beside

REPEAT PLAY.

6

Press the STATUS/EXIT button. Now, when a tape has fin- ished playing, the VCR will rewind it and start playback again.

SPEEDPAUSE/STILL

REC/OTR MEMORY

MUTE

Helpful Hints

•To cancel Repeat Play, follow steps 1 - 4 above. At step 5, press the F.FWD/B button so that OFF appears beside REPEAT PLAY. Press the STATUS/EXIT button.

•The real-time counter memory does not function during Repeat Play.

Image 33

Contents VRA211AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemPlug in the TV and the VCR CH3 CH4Connections Cable Signal RF coaxialRecording/Viewing Any Channel RF coaxial Cable TV’s ANTENNAJackConnect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Turning on Your VCR Press the VCR button, then press the Power button2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR buttonPress the Menu button Adding/Deleting Channels Automatic Channel Setup cont’dReviewing Memorized Channels Press the VCR button Press the Menu buttonPress the STATUS/EXIT button once or twice to exit Enter a 0 before a single-digit number Setting the ClockDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape in the VCR Insert a tape with its record tab intact in the VCR RecordingIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceVCR light will disappear from the VCR’s display panel Recording One Channel/Watching AnotherOne-Touch Recording Do each step within 60 seconds of the previous step Timer RecordingPress the VCR button, then press the Menu button DailyTimer Recording cont’d Timer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayButton to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on-screen, press the Clear Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Cable Box/DBS Output Channel 03 or GlossaryHelpful Hints Helpful Hints cont’d Specifications Model # Serial # Limited WarrantyIndex Page Supplied Accessories