Philips VRA211AT owner manual Automatic Operation Features

Page 36

36 Automatic Operation Features

The following playback features will always operate.

Automatic Playback

When you put a tape in the VCR, the power will come on auto- matically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automati- cally when you insert a tape with the record tab intact.

If a timer recording is set and the VCR power is off, the VCR will eject the tape if the record tab is missing.

Automatic Rewind, Eject, Off

When a tape is played, fast forwarded, or recorded to its end, the VCR will rewind the tape, stop, eject the tape, then turn itself off. If the real-time counter memory is set, the VCR will only rewind the tape to the point at which the counter is set to zero, then stop. The VCR will not eject the tape automatically or shut itself off.

Tape Eject

A tape can be ejected with the VCR power on or off (but the VCR must be plugged in). If a timer recording is set, a tape can only be ejected with the power on. Make sure you insert a tape and turn off the VCR power for the timer recording.

Automatic Tracking Adjustment

The VCR adjusts tracking automatically to give you the best possi- ble picture quality. With some recordings, however, you may get a better picture using the manual tracking controls (see below).

Manual Tracking

To manually adjust the tracking during playback, press the CHAN- NEL o/p buttons on the VCR. (The CH(annel) o/p button on the remote control will not adjust tracking.)

Tracking will return to Automatic Tracking Adjustment when you press the STOP/p button or insert a tape.

You cannot manually adjust the tracking of a Still picture. However, you may press the CHANNEL o/p buttons on the VCR to remove vertical jitter in a Still picture.

Before	After
Tracking	Tracking
Adjustment	Adjustment

Image 36

Contents VRA211AT Dear Philips Magnavox product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCH3 CH4 Plug in the TV and the VCRCable Signal RF coaxial ConnectionsRecording/Viewing Any Channel RF coaxial Cable TV’s ANTENNAJackCable Signal Connect a Cable signal to the VCR’s ANTenna in JackRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Press the VCR button, then press the Power button Turning on Your VCR2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR buttonPress the Menu button Automatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the VCR button Press the Menu buttonPress the STATUS/EXIT button once or twice to exit Setting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape in the VCR Recording Insert a tape with its record tab intact in the VCRIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Timer Recording Do each step within 60 seconds of the previous stepPress the VCR button, then press the Menu button DailyTimer Recording cont’d Timer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication RF coaxial cable Repeat Play Press the F.FWD/B button so that on appears besideButton to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on-screen, press the Clear Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel 03 orHelpful Hints Helpful Hints cont’d Specifications Limited Warranty Model # Serial #Index Page Supplied Accessories