Philips VRA211AT owner manual Timer Recording cont’d

Page 29

Timer Recording (cont’d) 29

4

Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on-screen.

NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on-screen briefly. Information about the program in that slot will appear on-screen. If this happens, press the STATUS/EXIT button, then select another number.

5

Use the Number buttons to enter the channel you want to record.

●Cable Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press

0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. There also may be a brief delay when you select channels 10, 11, and 12. If you want to select chan- nels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7. Antenna Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay. You may only select channels 2-69.

●If you are recording from line input, press 0,0 to select A/V IN.

●If you are using a Cable Box/DBS, select the Cable Box/DBS output channel (03 or 04). Set the Cable Box/DBS to the chan- nel you want to record. Leave the Cable Box/DBS on for the timer recording. See page eight for details.

4-7

POWER VCR/TV EJECT

VCR

TV

 

PLAY

 

REW

 

F.FWD

 

STOP

 

MENU

STATUS/EXIT

CLEAR

1

2

3

 

4

5

6

CH

 

7

8

9

 

 

 

ALT. CH

 

 

0

 

VOL

 

 

 

SPEED

 

PAUSE/STILL

 

REC/OTR

MEMORY

 

MUTE

6

Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

7

Follow the instructions in step 6 to enter the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

09:30 PM

TIME OFF

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

Instructions continue on page 30.

Helpful Hint

•Entries that do not match the VCR’s clock or calendar will cause a ques- tion mark to appear on-screen.

Page 28 Page 30
Image 29
Page 28 Page 30
Contents VRA211AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoIntroduction FeaturesSafety Precautions Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemPlug in the TV and the VCR CH3 CH4Connections Cable Signal RF coaxialRecording/Viewing Any Channel RF coaxial Cable TV’s ANTENNAJackConnect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Turning on Your VCR Press the VCR button, then press the Power button2Turn on the TV Press the Menu button. The display shown below will appearPress the Menu button Automatic Channel SetupPress the VCR button Adding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsPress the VCR button Press the Menu button Enter a 0 before a single-digit number Setting the ClockDaylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Insert a tape with its record tab intact in the VCR RecordingIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceVCR light will disappear from the VCR’s display panel Recording One Channel/Watching AnotherOne-Touch Recording Do each step within 60 seconds of the previous step Timer RecordingPress the VCR button, then press the Menu button DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Program REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsTimer recording information for the program in the lowest RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayWhile the status display is on-screen, press the Clear Button to reset the real-time counter to zeroReal-Time Counter Memory Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Cable Box/DBS Output Channel 03 or GlossaryHelpful Hints Helpful Hints cont’d Specifications Model # Serial # Limited WarrantyIndex Page Supplied Accessories
Top Page Image Contents