Chariot Carriers CX 2, CX 1 manual Storing the wheels arms and 16 wheel

Page 37

To correct directional trueness (ie. The carrier not rolling straight):

The dropouts of the wheel arms are screwed on and their holes are slotted. After loosening both screws, the dropout can be moved. This is possible on both the right-hand and the left-hand side dropout. If the Jogging Stroller is pulling to the right, the dropout on the right-hand side must be moved forwards, and the one on the left-hand side backwards (or vice versa).

WARNING

Please ensure that your child does not stand on the wheel arms when entering or leaving the carrier. If at any time you stop, do not allow anyone to sit on the wheel arms. Applying a load on either wheel arm may result in the aluminium axle sockets working loose.

DANGER

Always make sure that the large spring button of each wheel arm engages in the hole of the relevant Click ‘n’ Store bracket. If this is not done, the wheel arm might work loose and get caught in the wheel spokes. You run the risk of an accident!

3 straps are provided at the rear on the storage bag for attaching the 16” wheel. First of all thread correctly and then pull the top webbing strap tight. Then secure the wheel using the right and left-hand Velcro straps.

Storing the wheels arms and 16” wheel

If you want to convert the carrier from Jogging Stroller to another CTS Conversion Kit, or if you want to store the carrier, the wheel arms can be attached to the rear side of the carrier. The 16” wheel can be attached at the back of the rear storage bag.

For this the carrier must not be folded.

The wheel arm can be attached to a Click ‘n’ Store bracket on the rear side of the carrier. Press the small spring button in and insert the wheel arm in the groove provided for it in the Click ‘n’ Store bracket. Position the wheel arm to that the large spring button engages in the hole of the Click ‘n’ Store bracket. Always attach the right-hand wheel arm (as seen in the direction of travel) to the right-hand side of the carrier (as seen in the direction of travel) and the left-hand one to the left-hand side. The axle dropouts will then protrude inwards below the carrier.

DANGER

Always make sure that the wheel is attached securely.

Travelling

Always make sure you follow the Owner’s Manual for the brake system on the CX – please see Section 4.10.

DANGER

Your safety and the safety of your child in a dangerous situati- on may depend on correct use of the brake.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Cheetah 1, Cheetah 2, Cougar 1, Cougar 2, CX 1, CX Table of Contents Congratulations on buying this child transporter General ItemsIntended Use Explanation of symbols and instructions Overview of Components SafetySafety information for all travelling situations General safety instructionsSafety instructions for maintenance and repairs Safety instructions for carrying infantsDescription of the Ready Chassis Supplied as standardAssembling the Ready Chassis Assembly and folding upFolding up the Ready Chassis Wheel assemblyCougar and Cheetah Installing the handlebarSeat and Seatbelts Safety wrist strapHandlebar bag CX To fasten the child into the carrier, proceed as followsAdjusting the padded shoulder harness TIP Two-in-one weather cover Climate controlOpening the two-in-one weather cover SunscreenFront side air vent on the Cougar Side window on the CXStorage bags Larly to the upper mesh bag Adjusting the suspension Cougar and CXOperating the parking brake Cheetah and Cougar Use as a wheel brake Safety InstructionsUse as a parking brake Adjusting the brake system Case 1 Too much increase in brake lever play WrongrightStart by adjusting one of the wheels Case 2 Brakes pull unequally Basic adjustmentFine adjusting Carrier pulls to when the brake is appliedWheel fitting Wheel removalCleaning Care and maintenanceBrake cables Screw connectionsCycling Kit Safety instructions for use as a Bicycle TrailerChariot Cycling Kit Weber Cycling KitLegal requirements Performance characteristics when used as a Bicycle TrailerAssembling the reflectors and safety flag AssemblyFor the plastic wheels used on theCheetah Spoked wheels on the Cougar and the CXAttaching the hitcharm to CTS Ready Chassis Page Bicycle with solid axle Attaching the Axle-Mount ezHitchAttaching the carrier Fixing the Weber hitch to the bicycle Special features of the VersaWingFor this the carrier must not be folded Suitability of the bicycle used for towing UseTravelling Use as a pull wagon Jogging Kit Safety instructions for use as a Jogging StrollerJogging Kit Performance characteristics when used as a Jogging Stroller Page Storing the wheels arms and 16 wheel Safety instructions for use as a Stroller Weight distributionStrolling Kit Strolling KitPerformance characteristics Travelling Hiking Kit Safety instructions for use as a Hiking CarrierTIP XC Skiing Kit Safety instructions for use as an XC Skiing CarrierCheetah und Cougar Assembly Attaching the skis to the carrierIdentical for all models Fitting the ski arms to the carrierPutting on the waist belt Length adjustment of the ski armsWalking Kit Safety instructions for use as WalkerFitting the drawbars to the carrier Length adjustment of the drawbars Service, Care and Storage AccessoriesSpecifications Warranty and GuaranteeMileage in km Type of ride
Top Page Image Contents