Linear SLC, SLD, SLR manual Terminal Descriptions, Terminal Group Function

Terminal Descriptions

TERMINAL

GROUP

FUNCTION

AC N	24 VOLT INPUT	FACTORY CONNECTED TO 24 VAC FROM TRANSFORMER OR
AC		24 VDC FROM CONTINUOUS DUTY DC SUPPLY.
DC -	ACCESSORY POWER	PROVIDES 24 VOLT DC POWER FOR ACCESSORIES. (.5A MAX)
DC +
RESET	RESET BUTTON	FACTORY CONNECTED TO THE CONTROLLER’S RESET BUTTON.
COMMON
C
B	COMM LINK	FOR 3-WIRE NETWORK CONNECTION TO SECOND OPERATOR IN DUAL GATE INSTALLATIONS.
A
COMMON	SINGLE BUTTON INPUT	CONNECT TO NORMALLY OPEN SWITCH FOR SINGLE BUTTON OPERATION. ALTERNATES
SINGLE		BETWEEN OPEN-CLOSE OR OPEN-STOP-CLOSE DEPENDING ON PROGRAMMING.
COMMON	FIRE BOX INPUT	CONNECT TO NORMALLY OPEN SWITCH IN FIRE BOX FOR FIRE DEPARTMENT ACCESS.
FIRE DEPT
COMMON		CONNECT TO NORMALLY OPEN DEVICES (KEYPAD, CARD READER, KEYSWITCH,
	OPEN INPUT	TELEPHONE ENTRY SYSTEM) TO OPEN THE GATE. A CONSTANT OPEN INPUT WILL
OPEN
		OVERRIDE THE MID-TRAVEL STOP AND HALT THE AUTO CLOSE TIMER UNTIL RELEASED.
OPEN
CLOSE	3-BUTTON	CONNECT TO 3-BUTTON STATION FOR OPEN-CLOSE-STOP CONTROL. A CONSTANT OPEN INPUT
COMMON	STATION INPUT	WILL OVERRIDE THE MID-TRAVEL STOP AND HALT THE AUTO CLOSE TIMER UNTIL RELEASED.
STOP
COM		CONNECT TO NORMALLY OPEN DEVICES (GATE EDGE, PHOTO BEAM) TO DETECT AN
		OBSTRUCTION DURING OPENING. WHILE GATE IS IN MOTION, ANY OPEN OBSTRUCTION
O-OBS
		SIGNAL WILL CAUSE THE GATE TO STOP, REVERSE A SHORT DISTANCE, AND THEN
		STOP AGAIN. AT THIS TIME THE AUTO CLOSE TIMER IS DISABLED, AND A RENEWED
	OBSTRUCTION INPUTS	INPUT WILL BE REQUIRED TO START THE GATE AGAIN. SHOULD THE GATE BE
		RESTARTED AND THE OBSTACLE SIGNAL OCCUR AGAIN PRIOR TO REACHING A LIMIT,
		THE GATE WILL STOP AGAIN, LOCKOUT, AND SOUND THE EMERGENCY ALARM.
C-OBS		FUNCTIONS THE SAME AS THE OPEN OBSTRUCTION, EXCEPT IN THE CLOSING DIRECTION.
COM
COM	REVERSE	CONNECT TO NORMALLY OPEN DEVICES TO CAUSE A REVERSAL WHEN THE GATE IS
REV		TRAVELING CLOSED. THE GATE WILL REVERSE TO THE FULL OPEN POSITION.
OPEN LOOP		CONNECT TO OPEN LOOP/FREE EXIT LOOP. THE GATE WILL OPEN
	OPEN LOOP	WHEN THE LOOP IS TRIGGERED, AND REMAIN OPEN AS LONG AS
OPEN LOOP
		THE LOOP IS TRIGGERED. REQUIRES LOOP DETECTOR.
REVERSE LOOP		CONNECT TO REVERSE LOOP. TRIGGERING THE LOOP WILL CAUSE A
	REVERSE LOOP	REVERSAL WHEN THE GATE IS TRAVELING CLOSED. THE GATE WILL REVERSE
REVERSE LOOP
		TO THE FULL OPEN POSITION. REQUIRES LOOP DETECTOR.
SHADOW/RESET LOOP		CONNECT TO SHADOW/RESET LOOP TO KEEP THE GATE IN ITS FULLY OPEN
	SHADOW/RESET LOOP	POSITION AS LONG AS THE SIGNAL IS PRESENT. USED TO KEEP GATE OPEN
SHADOW/RESET LOOP
		WHILE VEHICLE IS PASSING THROUGH. REQUIRES LOOP DETECTOR.
-	ALARM	FACTORY CONNECTED TO THE ALARM BEEPER.
+
N.O.		FOR CONNECTION TO AUXILIARY DEVICES (MAGNETIC LOCK, SOLENOID LOCK,
COM	AUX RELAY
		STROBE LIGHT) FOR ACTIVATION (OR DEACTIVATION) DURING GATE OPERATION.
N.C.
+	24 VOLT SOLAR PANEL	FOR CONNECTION TO 24 VOLT SOLAR PANEL FOR BATTERY CHARGING.
-
+	24 VOLT BATTERY	FACTORY CONNECTED TO BATTERIES IN DC MODEL OPERATORS.
-

SLR • SLC • SLD  Slide Gate Operator Installation Guide - 9 - 227968 Revision X13 2-3-09