Linear SLD Advanced Controller Programming, Entering Advanced Programming Mode, Maximum Run Time

Advanced Controller Programming

Entering Advanced Programming Mode	FUNCTION				OPTIONS
To access and program the Advanced Programming functions, for each			"AD"			ADVANCED PROGRAMMING FUNCTIONS
						WILL NOT BE DISPLAYED
programming session, Advanced Programming must be enabled.						ADVANCED PROGRAMMING OPTIONS
After exiting programming, the Advanced Programming functions
						WILL BE DISPLAYED
will be available on the programming display during the next
programming session unless the operator has run 50 or more				PRESS UP OR
cycles. After that, Advanced Programming must be enabled again.				DOWN TO CYCLE			NOTE: ADVANCED PROGRAMMING
				THROUGH OPTIONS
Maximum Run Time							WILL STAY ENABLED AFTER
	ADVANCED			PRESS ENTER TO			EXITING PROGRAMMING UNTIL
The factory default for the Maximum Run Time is 99 seconds. When the	PROGRAMMING			SELECT AN OPTION			THE GATE CYCLES 50 TIMES
operator starts, a timer will begin counting. If a open or close limit is not
reached or an obstacle or reversing input is not received before the timer
	FUNCTION				OPTIONS
expires, the operator will stop, the unit locks out and the alarm sounds.
			"RT"			DISPLAY SHOWS CURRENT
The timer can be set for 10 to 99 seconds, but should be left at 99 in most
						MAXIMUM RUN TIME SETTING
applications. Setting it too close to the actual run time may cause the time
to expire with changing ambient temperature, gate conditions, etc…					ENTER PRESS ENTER FOR 1 SECOND
Single Button Input Setup						WHILE DISPLAY IS FLASHING, PRESS
This function is used for selecting the operation for single button controls						UP OR DOWN TO CHANGE THE
						MAXIMUM RUN TIME (10-99 SECONDS)
and radio receivers.
The factory default sets the SINGLE input terminal so successive inputs	MAXIMUM RUN				ENTER PRESS ENTER TO STORE THE VALUE
		TIMER
will cycle the operator in OPEN-STOP-CLOSE-STOP order.
Alternately, the SINGLE input can be set to cause the gate to OPEN
unless the gate is fully open. If the gate is fully open, the input will cause	FUNCTION				OPTIONS
						SINGLE INPUT WILL CYCLE OPERATOR
the gate to CLOSE.			"SB"
						IN ORDER OF OPEN-STOP-CLOSE-STOP
Stagger Mode (Rarely used in slide gate installations)						SINGLE INPUT WILL OPEN OPERATOR,
This function is used in dual gate installations only. The factory						IF OPERATOR IS ALREADY OPEN, SINGLE
						INPUT WILL CLOSE OPERATOR
default sets the Stagger Mode to OFF. In dual gate installations the two
				PRESS UP OR
operators communicate through the 3‑wire COMM LINK interface. When
				DOWN TO CYCLE
using the Stagger Mode, set one operator for delayed opening and the
				THROUGH OPTIONS
other operator for delayed closing. The Stagger Delay Time programming
	SINGLE BUTTON			PRESS ENTER TO
function (see below) sets the length of the delay.
	INPUT SETUP			SELECT AN OPTION

✓NOTE: This function will only be displayed if dual gate operation is

selected.
			FUNCTION					OPTIONS
Stagger Delay Time (Rarely used in slide gate installations)						"SM"			DISABLES STAGGER FUNCTION
This function is used in dual gate installations only. The factory
default sets the Stagger Time to 0 seconds (OFF). The Stagger Time					PRESS UP OR				SETS THIS OPERATOR FOR
sets the delay for the Stagger Mode. The Stagger Time can be set from					DOWN TO CYCLE				DELAYED OPEN
1-99 seconds.					THROUGH OPTIONS				SETS THIS OPERATOR FOR
					PRESS ENTER TO
✓ NOTE: This function will only be displayed if dual gate operation is
									DELAYED CLOSE
					SELECT AN OPTION
selected.
			STAGGER							DUAL GATES
This should be left at 99 seconds in most instances. Setting it close to the
				MODE						ONLY
actual run time may cause the timer to expire with changing temperature,
gate conditions, etc…
			FUNCTION					OPTIONS
						"ST"			STAGGER TIMER DISABLED
									SET STAGGER DELAY VALUE
									1 TO 99 SECONDS
							PRESS UP OR
							DOWN TO CYCLE
							THROUGH OPTIONS
			STAGGER				PRESS ENTER TO			DUAL GATES
			DELAY TIME				SELECT AN OPTION			ONLY
	- 13
SLR • SLC • SLD  Slide Gate Operator Installation Guide		-							227968 Revision X13 2-3-09