Linear SLD Error Indications, Entrapment, Comm Link Connection Failure, Maximum Run Time Exceeded

Page 27

Error Indications

During abnormal operation, the Controller’s displays and beeper will indicate the error condition that has occurred..

Entrapment

If an entrapment condition occurs detected by two repeated open or close obstruction triggers, the Controller will lock the operator out.. The beeper will sound constantly and the gate will not operate.. To reset the Controller press the STOP button or press the RESET button on the operator’s cover..

  WARNING 

The Stop and/or Reset button must be located in the line-of- sight of the gate. Activation of the reset control shall not cause the operator to start.

COMM LINK Connection Failure

In dual gate installations, if there is a connection failure between the two operators, the COMM LINK indicator will blink once a second.. During this condition the gate will not operate, except if triggered by the FIRE DEPT input, which functions normally..

MGT Obstacle Transmitter Trouble

If any MGT transmitters are used with the operator, their supervision feature will alert the Controller if there is any trouble with the transmitter.. MGT transmitters send hourly status reports and will send low battery reports when the transmitter has a low battery.. The MGT transmitters also have a tamper detection switch that will trigger when their case is opened..

When the Controller detects a low transmitter battery, a tamper signal, or missing transmitter status reports, the gate will still operate normally, but the beeper will change as follows:

The Pre-start Alarm will beep twice as fast.

The Run Alarm will beep twice as fast and continue for five minutes after the gate stops.

The sounder will “chirp” every five seconds when the gate is idle.

Correct the trouble (close case, replace battery, or replace transmitter) to clear the obstacle transmitter trouble indications..

Maximum Run Time Exceeded

If the Maximum Run Time is exceeded, the Controller stops the operator the same as if a double obstacle has occurred in an entrapment condition.. The entrapment alarm sounds constantly, and is cleared by pressing the STOP button or the RESET button on the cover.. After the STOP or RESET button is pressed, because the Maximum Run Time has been exceeded, the sounder will beep twice every five seconds.. The next operation of the gate will clear the indication..

CONTROLLER ERROR CAUSES AND INDICATIONS

ERROR CAUSE

ERROR INDICATION

HOW TO CLEAR

 

 

 

TWO SAFETY REVERSALS (ON

En 00, CONTINUOUS ALARM

 

SINGLE GATE OR ON EITHER

PRESS STOP BUTTON

BEEPER, GATE DISABLED

DUAL GATE)

 

 

 

 

 

PRESS STOP BUTTON,

MAXIMUM RUN TIMER

En 01, AND MAX RUN LED,

CLEARS CONTINUOUS ALARM,

CONTINUOUS ALARM BEEPER,

THEN DOUBLE BEEP EVERY

EXCEEDED ON OPENING

GATE DISABLED

5 SECONDS UNTIL NEXT

 

 

 

OPERATION

 

 

PRESS STOP BUTTON,

MAXIMUM RUN TIMER

En 02, AND MAX RUN LED,

CLEARS CONTINUOUS ALARM,

CONTINUOUS ALARM BEEPER,

THEN DOUBLE BEEP EVERY

EXCEEDED ON CLOSING

GATE DISABLED

5 SECONDS UNTIL NEXT

 

 

 

OPERATION

 

En 03, AND COMM LINK LED,

 

COMM LINK FAILURE

CONTINUOUS ALARM BEEPER

PRESS STOP BUTTON, CLEARS

FOR 1 MINUTE, GATE DISABLED

CONTINUOUS ALARM

 

 

(EXCEPT FOR FIRE DEPT INPUT)

 

GATE FULL OPEN RESULTING

En 04, GATE DISABLED

PRESS STOP BUTTON

FROM FIRE DEPT INPUT

 

 

FAIL SAFE OR FAIL SECURE

En 05, GATE DISABLED

BATTERY VOLTAGE MUST RISE

BECAUSE OF AC POWER LOSS

ABOVE 24 VDC

 

OTHER CONTROLLER IN

En 06, GATE DISABLED

CLEAR ENTRAPMENT ON OTHER

ENTRAPMENT (DUAL GATE)

CONTROLLER (PRESS STOP)

 

LOW AC VOLTAGE AT

En 07, GATE DISABLED

LOW VOLTAGE AC POWER MUST

CONTROLLER

RISE ABOVE 20 VAC

 

INPUT TRIGGERED DURING

En 08, GATE DISABLED

PRESS STOP BUTTON

ENTRAPMENT LOCKOUT

 

 

COMPATIBILITY PROBLEM

En 09, GATE DISABLED

UPDATE FIRMWARE AND RESET

BOTH PAIRED CONTROLLERS

 

 

EEPROM PROBLEM

En 10, GATE DISABLED

TRY RESET, CALL TECH. SUPPORT

 

 

REPROGRAM MOTOR TYPE OR

DC MOTOR MISMATCH

En 11, GATE DISABLED

CHANGE DC MOTOR BOARD,

NEXT GATE MOVEMENT WILL

 

 

 

 

RETRY DC MOTOR CHECK

MOTOR FAILURE

En 12, GATE DISABLED

REPLACE MOTOR

MGT SUPERVISORY CONDITION

FAST BEEPS DURING PRESTART,

CLEARS WHEN MGT CONDITION

(TAMPER, LOW BATTERY,

FAST BEEP RUN ALARM, CHIRP

CLEARS

MISSING HOURLY STATUS)

EVERY 5 SECONDS AT IDLE

 

SLR SLC SLD  Slide Gate Operator Installation Guide

- 25 -

227968 Revision X13 2-3-09

Image 27
Contents SLR SLC SLD Table of Contents Gate Operator Classifications Before You BeginAlways Check the Gate’s Action Regulatory WarningsWiring Specifications AC Power WiringDC Control and Accessory Wiring Gate Post Mounting Pad InstallationMounting Pad Specifications Gate PreparationEND of Gate Pipe Shown Reference only Gate Bracket and Chain AssemblyOperator Preparation Operator SetupLimit Nuts Rough Adjustment Limit Nuts Fine AdjustmentRIGHT-HAND Installation Connectors Controller FeaturesBlinks if Connection has Failed Maint Alert SET Indicator DescriptionsTerminal Group Function Terminal DescriptionsOperator Accessory Connections Operator Accessory ConnectionsBasic Controller Programming Run Alarm and Pre-start Alarm Maximum Open Direction Current SettingMaximum Close Direction Current Setting Maximum Run Time Entering Advanced Programming ModeSingle Button Input Setup Advanced Controller ProgrammingPower Failure Mode Auxiliary Relay ModeReverse Delay Time Low Power ModeMid-travel Stop Position Reset Cycle CountMaintenance Alert Trigger Soft Start/Stop DurationRadio Transmitter Learn Radio EnableAntenna Installation Reset Controller to Factory DefaultsSLR SLC SLD  Loop Layout IllustrationLoop Sealant USE Relief Cuts AT CornersSafety Edge Layout Illustration Safety Edge Layout Illustration #2 Photoeye Installation Illustration Pickets Space Smaller than 2 1/4 Entrapment Zone #3Entrapment Zone #1 Gate Bracket Bolted to Channel Track Gate InstallationShield Dual Gate InstallationsOpen and Close Limit settings Operator #1Operation Indications Gate OperationMGT Obstacle Transmitter Trouble Error IndicationsEntrapment Comm Link Connection FailureTroubleshooting Optional Parts Model SLR Exploded ViewOptional Torque Limiter Model SLC Exploded ViewCapacitors For drives 34 to 47 feet wideLimiter Model SLD Exploded ViewModel SLD Mechanical Parts List When NEW Model SLD MaintenanceBattery Maintenance DC Motor Brush ReplacementGeneral Preventative MaintenanceMonth Preventative Maintenance FCC NoticeInstaller Customer Gate Operator Installation Checklist