Linear SLC, SLD, SLR manual Gate Operation, Operation Indications

Page 26

Gate Operation

Open Button

Opens the gate.. If the Controller is programmed to stop opening the gate at mid-travel, a constant press of the OPEN button will override the Mid‑travel Stop and completely open the gate.. If the Auto Close Timer is set, it will be suspended until the OPEN button is released..

Close Button

Closes the gate if the gate is open.. Also closes the gate if the gate is in the process of opening..

Stop Button

Stops the gate from opening or closing at any time..

Single Input

Opens the gate if it’s closed and closes the gate if it’s open (open-close programming option).. Activating the input while the gate is moving will reverse the gate..

Can be programmed to stop the gate while the gate is moving (open-stop-close programming option)..

Fire Department Input

Fully opens the gate when the input is activated.. Overrides the Mid-travel Stop and Auto Close Timer (if either is programmed for the gate).. The gate will lockout in the open position without sounding the alarm.. Press the STOP button to release the lockout..

Open Input

Functions the same as the OPEN button..

Open Obstruction

While the gate opening, any open obstruction signal will cause the gate to stop, reverse a short distance, and then stop again.. The Auto Close Timer will be disabled, and a renewed input will be required to start the gate again.. Should the gate be restarted and the obstacle signal occur again prior to reaching a limit, the gate will stop again, lockout, and sound the emergency alarm..

Close Obstruction

Same as the open obstruction, but in the closing direction..

Reverse Input

If the reverse input is triggered while the gate is closing, the gate will reverse to the full open position.. If the Auto Close Timer is set, when the reverse input is cleared, the gate will close when the Auto Close Timer expires..

Open Loop

Functions the same as the OPEN button..

Reverse Loop

Functions the same as the reverse input..

Shadow/reset Loop

Only used with Swing Gates.. Holds the gate fully open or fully closed while triggered.. If open, the gate closes immediately when cleared..

Operation Indications

During normal operation, the Controller’s displays will indicate current operating conditions and status..

Power-up Display

When the Controller powers up, dashes will show on the display for one second, then the firmware version number will be displayed for one second..

Exiting programming restarts the Controller.. The power-up display will show upon the restart..

Idle Condition

While the Controller is idling, waiting for a command, the display will show circulating dashes..

For DC models only - Clockwise : Batteries discharging, Counterclockwise : Batteries charging..

Last Gate Position/Condition

When the gate moves or stops, the display will show the status for up to one minute..

•Stop is displayed as St

•Full Close is displayed as FC

•Full Open is displayed as FO

•Entrapment is displayed as En

Pre-start Delay

During the pre-start delay, the display will countdown the number of seconds remaining before the operator starts..

Reverse Delay

If the gate travel direction is reversed from a user activation or reversing device, and a reverse delay is set, the display will count down the delay time in seconds before the operator restarts..

Run Timer

While the gate is opening or closing, the number of seconds running time is displayed..

SLR • SLC • SLD  Slide Gate Operator Installation Guide

- 24 -

227968 Revision X13 2-3-09

Page 25 Page 27
Image 26
Page 25 Page 27
Contents SLR SLC SLD Table of Contents Regulatory Warnings Before You BeginAlways Check the Gate’s Action Gate Operator ClassificationsDC Control and Accessory Wiring Wiring SpecificationsAC Power Wiring Gate Preparation Mounting Pad InstallationMounting Pad Specifications Gate PostGate Bracket and Chain Assembly END of Gate Pipe Shown Reference onlyOperator Setup Operator PreparationRIGHT-HAND Installation Limit Nuts Rough AdjustmentLimit Nuts Fine Adjustment Controller Features ConnectorsIndicator Descriptions Blinks if Connection has Failed Maint Alert SETTerminal Descriptions Terminal Group FunctionOperator Accessory Connections Operator Accessory ConnectionsBasic Controller Programming Maximum Close Direction Current Setting Run Alarm and Pre-start AlarmMaximum Open Direction Current Setting Advanced Controller Programming Entering Advanced Programming ModeSingle Button Input Setup Maximum Run TimeLow Power Mode Auxiliary Relay ModeReverse Delay Time Power Failure ModeSoft Start/Stop Duration Reset Cycle CountMaintenance Alert Trigger Mid-travel Stop PositionReset Controller to Factory Defaults Radio EnableAntenna Installation Radio Transmitter LearnUSE Relief Cuts AT Corners Loop Layout IllustrationLoop Sealant SLR SLC SLD Safety Edge Layout Illustration Safety Edge Layout Illustration #2 Photoeye Installation Illustration Entrapment Zone #1 Pickets Space Smaller than 2 1/4Entrapment Zone #3 Track Gate Installation Gate Bracket Bolted to ChannelOperator #1 Dual Gate InstallationsOpen and Close Limit settings ShieldGate Operation Operation IndicationsComm Link Connection Failure Error IndicationsEntrapment MGT Obstacle Transmitter TroubleTroubleshooting Model SLR Exploded View Optional PartsModel SLC Exploded View Optional Torque LimiterFor drives 34 to 47 feet wide CapacitorsModel SLD Exploded View LimiterModel SLD Mechanical Parts List DC Motor Brush Replacement Model SLD MaintenanceBattery Maintenance When NEWFCC Notice Preventative MaintenanceMonth Preventative Maintenance GeneralGate Operator Installation Checklist Installer Customer
Top Page Image Contents