AT&T 8000 installation instructions House Code DIP Switch Combinations

Page 20

House Code DIP SWITCH Combinations

House	House Code Dip Switch Settings
Code	1	2	3	4	5	6	7

000OFF OFF OFF OFF OFF OFF OFF

001OFF OFF OFF OFF OFF OFF ON

002OFF OFF OFF OFF OFF ON OFF

003OFF OFF OFF OFF OFF ON ON

004OFF OFF OFF OFF ON OFF OFF

005OFF OFF OFF OFF ON OFF ON

006OFF OFF OFF OFF ON ON OFF

007OFF OFF OFF OFF ON ON ON

008OFF OFF OFF ON OFF OFF OFF

009OFF OFF OFF ON OFF OFF ON

010OFF OFF OFF ON OFF ON OFF

011OFF OFF OFF ON OFF ON ON

012OFF OFF OFF ON ON OFF OFF

013OFF OFF OFF ON ON OFF ON

014OFF OFF OFF ON ON ON OFF

015OFF OFF OFF ON ON ON ON

016OFF OFF ON OFF OFF OFF OFF

017OFF OFF ON OFF OFF OFF ON

018OFF OFF ON OFF OFF ON OFF

019OFF OFF ON OFF OFF ON ON

020OFF OFF ON OFF ON OFF OFF

021OFF OFF ON OFF ON OFF ON

022OFF OFF ON OFF ON ON OFF

023OFF OFF ON OFF ON ON ON

024OFF OFF ON ON OFF OFF OFF

025OFF OFF ON ON OFF OFF ON

026OFF OFF ON ON OFF ON Off

027OFF OFF ON ON OFF ON ON

028OFF OFF ON ON ON OFF OFF

029OFF OFF ON ON ON OFF ON

030OFF OFF ON ON ON ON OFF

031OFF OFF ON ON ON ON ON

House House Code Dip Switch Settings

Code	1	2	3	4	5	6	7
032	OFF	ON OFF OFF OFF OFF O F F
033	OFF ON		OFF OFF OFF OFF ON
034	OFF ON		OFF OFF OFF ON O F F
035	OFF ON		OFF	OFF	OFF	ON	ON

036OFF ON OFF OFF ON OFF OFF

037OFF ON OFF OFF ON OFF ON

038OFF ON OFF OFF ON ON OFF

039OFF ON OFF OFF ON ON ON

040OFF ON OFF ON OFF OFF O F F

041OFF ON OFF ON OFF OFF ON

042OFF ON OFF ON OFF ON OFF

043OFF ON OFF ON OFF ON ON

044OFF ON OFF ON. ON OFF OFF

045OFF ON OFF ON ON OFF ON

046OFF ON OFF ON ON ON OFF

047OFF ON OFF ON ON ON ON

048OFF ON ON OFF OFF OFF OFF

O49 OFF ON ON OFF OFF OFF ON

050OFF ON ON OFF OFF ON OFF

051OFF ON ON OFF OFF ON ON

052	OFF ON	ON OFF ON OFF OFF
053	OFF ON	ON OFF ON OFF ON
054	OFF ON	ON OFF ON ON OFF
055	OFF ON	ON	OFF ON ON ON
056	OFF ON	ON	ON OFF OFF OFF

057OFF ON ON ON OFF OFF ON

058OFF ON ON ON OFF ON OFF

059OFF ON ON ON OFF ON ON

060OFF ON ON ON ON OFF OFF

061OFF ON ON ON ON OFF ON

062OFF ON ON ON ON ON OFF

063OFF ON ON ON ON ON ON

AT&T Proprietary Information

2-19

Image 20

Contents AT&T Security System Pursuant to Company InstructionsService is all about Exceeding those expectations is what AT&T is all aboutSystem KnowledgcGood Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Chart to help determine what you need. Outline Obtain the floor plan and component list/work orderWhich are part of the AT&T Security Survey Call the customer to verify the time and locationCommon Hand Tools Slotted-Head Screwdriver Phillips-Head ScrewdriverRequirements WiringEnvironment Page Meet the Customer Confirm Correct Location Salesman has told him/herYou can answer any questions before you leave Look for broken windows, scratched paint, torn wallpaperPaper mills Choose Central Controller Location PrecautionsLarge neighborhood antennas Objects MetaI kitchen or bathroom cupboardsRefrigerators MetaI sinks and tubsWireless Remote Transmitter Keypad Transmitter ISI Wireless Siren ControllerAntenna Placement Transmitter locationsAntenna length less than I5 feet, if possible ThemPossible Antenna Run in a Multi-level Home Transformer Signal must pass through several outer walls Wire lath in plaster wallsProblems, especially in L shaped homes InsulationHouse code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Install the Digital Communicator Environmental17Problem. Reset the watchdog with the AT&T Model Possible. Sharp angles in the wiring run reduceProgram the Digital Communicator using the AT&T Remote Programming PackageRun the Central Controller Antenna Choose the antenna run It is critical that you identifySources of possible RF interference Potential blocks to RF wavesPower Up the Central Controller Plug in the Transformer Verify powerEnter the Installer Test Mode Digital displayAllow at least two inches between the unit and the ceiling Choose Transmitter Mounting LocationsKeypad Transmitter Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Wireless Remote/Transmitter Alarm Hour Sensor Loop Not SecureBattery is OK CONDITlONSensor Run the Phone Line for the Digital Communicator Locate the phone line protector blockStep LYll Then install the High Power Siren Requires more powcr than 450 MARelay Module Recheck All Transmitter LocationsBeeps and alarms to specific transmitters. Code numbers Program the TransmittersLet’s look at the I.D. Code for a moment Number is used by the Central Controller to relay trouble1171 Selectable sensor loop zone House code setting Wireless Remote/Transmitter DIP SwitchesProgramming Selectable sensor loop optionSet House Code/Option DIP Switches = closed loop= high security = low securityPage White Wire Yellow Wire Third Number 1st = B 2nd = WPage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Housing Press up on the tab at the bottomIntrusion Audible Panic Interior Auxiliary EnvironmentalAT&T Proprietary Information Lens Replace lens brackets carefully Transmitter PIR TAT&T Proprietary Information PscH8$E Active Post on Pirt Circuit BoardPage Use the information presented in the Installation Open the detector front housingAccessed through a small hole in the backplate Set the House code DIP switches$t.ns~ Switch Page Mount the backplate Mount the Transmitters Mount Wireless Remote/TransmitterSensor manufacturer’s instructions USE Jumpers To Close Loops For Handheld USE Attach the front housing Mount Keypad TransmitterMount Universal Transmitter Page Panic APPLlCATiONS Auxiliary APPLlCATlONSReduce the sensitivity of the Pirt by using Comes on when you moveSeveral minutes to stabilize Walk test the Pirt to verify its coverageExit the Installer Test Mode On = Silent OFF = Sound Switch 9 should Always be on Choose the Wireless Siren /ControllerSources of possible RF interference Potential blocks to RF wavesScrew provided #6-32 Verify that the AC Power Light is onTransformer Plug in the transformer Until 1 Beep is heard System Test Hardwired Perform the System TestSystem Test 24-Hour Zone Transmitters RF Scanner