AT&T 8000 installation instructions $t.ns~ Switch

Page 63

Use the chart below to set the 3-DIGIT smoke detector identification number. Only I.D. numbers 24 through 31 are available for the Smoke Detectors.

	;$t.ns~;	1		l,D Switch	ring 3

	24		ON	ON	ON
	25		OFF	ON	ON
	26		ON	OFF	ON
	27		OFF	OFF	ON
	26		ON	ON	OFF
	29		OFF	ON	OFF
	30		ON	OFF	OFF
	31		OFF	OFF	OFF

4.Close the detector front housing.

5.Check the voltage on the batteries then connect them. Check the current draw.

NOTE: Use only Duracell NM 1604 batteries.

6.Log the transmitter location on the Central controller Zone Locator Card.

7.Temporarily place the detector in the area it will be mounted.

8.Perform the Supervised Smoke Detector Transmitter RF link test.

AT&T Proprietary Information 2-62

Image 63

Contents Pursuant to Company Instructions AT&T Security SystemKnowledgc Service is all aboutExceeding those expectations is what AT&T is all about SystemGood Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Call the customer to verify the time and location Chart to help determine what you need. OutlineObtain the floor plan and component list/work order Which are part of the AT&T Security SurveyPhillips-Head Screwdriver Common Hand Tools Slotted-Head ScrewdriverWiring EnvironmentRequirements Page Look for broken windows, scratched paint, torn wallpaper Meet the Customer Confirm Correct LocationSalesman has told him/her You can answer any questions before you leaveChoose Central Controller Location Precautions Large neighborhood antennasPaper mills MetaI sinks and tubs ObjectsMetaI kitchen or bathroom cupboards RefrigeratorsKeypad Transmitter ISI Wireless Siren Controller Wireless Remote TransmitterThem Antenna PlacementTransmitter locations Antenna length less than I5 feet, if possiblePossible Antenna Run in a Multi-level Home Transformer Insulation Signal must pass through several outer wallsWire lath in plaster walls Problems, especially in L shaped homesHouse code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Environmental17 Install the Digital CommunicatorRemote Programming Package Problem. Reset the watchdog with the AT&T ModelPossible. Sharp angles in the wiring run reduce Program the Digital Communicator using the AT&TPotential blocks to RF waves Run the Central Controller Antenna Choose the antenna runIt is critical that you identify Sources of possible RF interferencePlug in the Transformer Verify power Power Up the Central ControllerDigital display Enter the Installer Test ModeChoose Transmitter Mounting Locations Keypad TransmitterAllow at least two inches between the unit and the ceiling Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation CONDITlON Wireless Remote/TransmitterAlarm Hour Sensor Loop Not Secure Battery is OKSensor Locate the phone line protector block Run the Phone Line for the Digital CommunicatorStep LYll Recheck All Transmitter Locations Then install the High Power SirenRequires more powcr than 450 MA Relay ModuleNumber is used by the Central Controller to relay trouble Beeps and alarms to specific transmitters. Code numbersProgram the Transmitters Let’s look at the I.D. Code for a moment1171 Selectable sensor loop option Selectable sensor loop zone House code settingWireless Remote/Transmitter DIP Switches Programming= low security Set House Code/Option DIP Switches= closed loop = high securityPage Yellow Wire Third Number 1st = B 2nd = W White WirePage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Press up on the tab at the bottom HousingIntrusion Audible Panic Interior Environmental AuxiliaryAT&T Proprietary Information Transmitter PIR T Lens Replace lens brackets carefullyAT&T Proprietary Information Active Post on Pirt Circuit Board PscH8$EPage Set the House code DIP switches Use the information presented in the InstallationOpen the detector front housing Accessed through a small hole in the backplate$t.ns~ Switch Page Mount the Transmitters Mount Wireless Remote/Transmitter Sensor manufacturer’s instructionsMount the backplate USE Jumpers To Close Loops For Handheld USE Mount Keypad Transmitter Attach the front housingMount Universal Transmitter Page Auxiliary APPLlCATlONS Panic APPLlCATiONSWalk test the Pirt to verify its coverage Reduce the sensitivity of the Pirt by usingComes on when you move Several minutes to stabilizeExit the Installer Test Mode Potential blocks to RF waves On = Silent OFF = Sound Switch 9 should Always be onChoose the Wireless Siren /Controller Sources of possible RF interferenceVerify that the AC Power Light is on Transformer Plug in the transformerScrew provided #6-32 Until 1 Beep is heard Perform the System Test System Test HardwiredSystem Test 24-Hour Zone Transmitters RF Scanner