AT&T 8000 installation instructions Mount Keypad Transmitter, Attach the front housing

Page 67

7.Perform the sensor activation RF test.

This test is used to verify the correct functioning of the sensor and the RF link of the mounted transmitter.

a.Activate the sensor.

b.Listen for the proper number of beeps from the Central Controller.

c.Check the Central Controller to verify that the proper transmitter I.D. number appears.

d.Check the status LEDs on the Central Controller for more information.

Mount Keypad Transmitter

1.

Mount the sensor to be used with the transmitter.

Follow the sensor manufacturer’s instructions.

2.Thread sensor wires through the Keypad Transmitter backplate.

3.Mount the backplate.

Be careful not to over-tighten the backplate screws.

4.Connect sensor wires to the screw terminals on the backplate for the desired type of sensor loop.

5.Connect the snap caps or spade lug wires to the screw terminals.

6.Attach the front housing.

AT&T Proprietary Information

2-66

Image 67

Contents Pursuant to Company Instructions AT&T Security SystemKnowledgc Service is all aboutExceeding those expectations is what AT&T is all about SystemGood Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Call the customer to verify the time and location Chart to help determine what you need. OutlineObtain the floor plan and component list/work order Which are part of the AT&T Security SurveyPhillips-Head Screwdriver Common Hand Tools Slotted-Head ScrewdriverEnvironment WiringRequirements Page Look for broken windows, scratched paint, torn wallpaper Meet the Customer Confirm Correct LocationSalesman has told him/her You can answer any questions before you leaveLarge neighborhood antennas Choose Central Controller Location PrecautionsPaper mills MetaI sinks and tubs ObjectsMetaI kitchen or bathroom cupboards RefrigeratorsKeypad Transmitter ISI Wireless Siren Controller Wireless Remote TransmitterThem Antenna PlacementTransmitter locations Antenna length less than I5 feet, if possiblePossible Antenna Run in a Multi-level Home Transformer Insulation Signal must pass through several outer wallsWire lath in plaster walls Problems, especially in L shaped homesHouse code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Environmental17 Install the Digital CommunicatorRemote Programming Package Problem. Reset the watchdog with the AT&T ModelPossible. Sharp angles in the wiring run reduce Program the Digital Communicator using the AT&TPotential blocks to RF waves Run the Central Controller Antenna Choose the antenna runIt is critical that you identify Sources of possible RF interferencePlug in the Transformer Verify power Power Up the Central ControllerDigital display Enter the Installer Test ModeKeypad Transmitter Choose Transmitter Mounting LocationsAllow at least two inches between the unit and the ceiling Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation CONDITlON Wireless Remote/TransmitterAlarm Hour Sensor Loop Not Secure Battery is OKSensor Locate the phone line protector block Run the Phone Line for the Digital CommunicatorStep LYll Recheck All Transmitter Locations Then install the High Power SirenRequires more powcr than 450 MA Relay ModuleNumber is used by the Central Controller to relay trouble Beeps and alarms to specific transmitters. Code numbersProgram the Transmitters Let’s look at the I.D. Code for a moment1171 Selectable sensor loop option Selectable sensor loop zone House code settingWireless Remote/Transmitter DIP Switches Programming= low security Set House Code/Option DIP Switches= closed loop = high securityPage Yellow Wire Third Number 1st = B 2nd = W White WirePage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Press up on the tab at the bottom HousingIntrusion Audible Panic Interior Environmental AuxiliaryAT&T Proprietary Information Transmitter PIR T Lens Replace lens brackets carefullyAT&T Proprietary Information Active Post on Pirt Circuit Board PscH8$EPage Set the House code DIP switches Use the information presented in the InstallationOpen the detector front housing Accessed through a small hole in the backplate$t.ns~ Switch Page Sensor manufacturer’s instructions Mount the Transmitters Mount Wireless Remote/TransmitterMount the backplate USE Jumpers To Close Loops For Handheld USE Mount Keypad Transmitter Attach the front housingMount Universal Transmitter Page Auxiliary APPLlCATlONS Panic APPLlCATiONSWalk test the Pirt to verify its coverage Reduce the sensitivity of the Pirt by usingComes on when you move Several minutes to stabilizeExit the Installer Test Mode Potential blocks to RF waves On = Silent OFF = Sound Switch 9 should Always be onChoose the Wireless Siren /Controller Sources of possible RF interferenceTransformer Plug in the transformer Verify that the AC Power Light is onScrew provided #6-32 Until 1 Beep is heard Perform the System Test System Test HardwiredSystem Test 24-Hour Zone Transmitters RF Scanner