AT&T 8000 installation instructions Environmental17, Install the Digital Communicator

Page 24

STEP 7

Install the Digital Communicator

NOTE: The 8700 Digital Communicator is probably installed. If it’s not, please follow these steps.

1.Plug the 8 wire ZONE INPUT connector into the Digital Communicator.

2.Plug the polarized 2 wire power connector into the Digital Communicator.

3.Peel off the protective backing from the two adhesive strips on the back of the Digital Communicator, Mount the Digital Communicator in the lower right hand side of the AT&T 8720 Central Controller.

4.Wire the Channel connector to the AT&T 8720 Central Controller.

Color Channel 1 Controller Terminal 1 Color 1 Channel 1 Controller Terminal

brown	1 1	1 fire (15)	1	green 1	5	1	interior(19)

o r a n g e	3	1 environmental(17)	1	violet	1 7	1	ambush(21)

5.Connect the black wire to terminal (U) and the red to terminal (14) of the AT&T 8720 Central Controller. The Digital Communicator is circuit protected against polarity reversal. The 1 amp fast blow fuse protects against excessive power consumption.

CAUTlON: Do not connect to any other power source. Voltages greater than 16 volts can damage the Digital communicator.

AT&T Proprietary Information

2-23

Image 24

Contents AT&T Security System Pursuant to Company InstructionsService is all about Exceeding those expectations is what AT&T is all aboutSystem KnowledgcGood Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Chart to help determine what you need. Outline Obtain the floor plan and component list/work orderWhich are part of the AT&T Security Survey Call the customer to verify the time and locationCommon Hand Tools Slotted-Head Screwdriver Phillips-Head ScrewdriverWiring EnvironmentRequirements Page Meet the Customer Confirm Correct Location Salesman has told him/herYou can answer any questions before you leave Look for broken windows, scratched paint, torn wallpaperChoose Central Controller Location Precautions Large neighborhood antennasPaper mills Objects MetaI kitchen or bathroom cupboardsRefrigerators MetaI sinks and tubsWireless Remote Transmitter Keypad Transmitter ISI Wireless Siren ControllerAntenna Placement Transmitter locationsAntenna length less than I5 feet, if possible ThemPossible Antenna Run in a Multi-level Home Transformer Signal must pass through several outer walls Wire lath in plaster wallsProblems, especially in L shaped homes InsulationHouse code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Install the Digital Communicator Environmental17Problem. Reset the watchdog with the AT&T Model Possible. Sharp angles in the wiring run reduceProgram the Digital Communicator using the AT&T Remote Programming PackageRun the Central Controller Antenna Choose the antenna run It is critical that you identifySources of possible RF interference Potential blocks to RF wavesPower Up the Central Controller Plug in the Transformer Verify powerEnter the Installer Test Mode Digital displayChoose Transmitter Mounting Locations Keypad TransmitterAllow at least two inches between the unit and the ceiling Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Wireless Remote/Transmitter Alarm Hour Sensor Loop Not SecureBattery is OK CONDITlONSensor Run the Phone Line for the Digital Communicator Locate the phone line protector blockStep LYll Then install the High Power Siren Requires more powcr than 450 MARelay Module Recheck All Transmitter LocationsBeeps and alarms to specific transmitters. Code numbers Program the TransmittersLet’s look at the I.D. Code for a moment Number is used by the Central Controller to relay trouble1171 Selectable sensor loop zone House code setting Wireless Remote/Transmitter DIP SwitchesProgramming Selectable sensor loop optionSet House Code/Option DIP Switches = closed loop= high security = low securityPage White Wire Yellow Wire Third Number 1st = B 2nd = WPage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Housing Press up on the tab at the bottomIntrusion Audible Panic Interior Auxiliary EnvironmentalAT&T Proprietary Information Lens Replace lens brackets carefully Transmitter PIR TAT&T Proprietary Information PscH8$E Active Post on Pirt Circuit BoardPage Use the information presented in the Installation Open the detector front housingAccessed through a small hole in the backplate Set the House code DIP switches$t.ns~ Switch Page Mount the Transmitters Mount Wireless Remote/Transmitter Sensor manufacturer’s instructionsMount the backplate USE Jumpers To Close Loops For Handheld USE Attach the front housing Mount Keypad TransmitterMount Universal Transmitter Page Panic APPLlCATiONS Auxiliary APPLlCATlONSReduce the sensitivity of the Pirt by using Comes on when you moveSeveral minutes to stabilize Walk test the Pirt to verify its coverageExit the Installer Test Mode On = Silent OFF = Sound Switch 9 should Always be on Choose the Wireless Siren /ControllerSources of possible RF interference Potential blocks to RF wavesVerify that the AC Power Light is on Transformer Plug in the transformerScrew provided #6-32 Until 1 Beep is heard System Test Hardwired Perform the System TestSystem Test 24-Hour Zone Transmitters RF Scanner