AT&T 8000 installation instructions Enter the Installer Test Mode, Digital display

Page 28

STEP 10

a. Enter the transmitter security code and then press the OFF key

Enter the Installer Test Mode

to put the system in the OFF state.

b. Press the Test/Demo key on the Central Controller. The

digital display will show an ‘88’.

Note: Quickly press the Test/Demo key. If it’s held down for

more than 3 seconds, the Demonstration Mode will be entered

instead of the installer Test Mode and a “-0.” will appear in the

digital display.

c. Touch alI four keys on the Central Controller at the same time

(Messages, Clear Display, Cancel, and Test/Demo). The digital

display will show a ‘CC’. See illustration below.

d. Listen for the Installer Test Mode indiation beeps to start.

There will be one beep every forty seconds.

AT&T Proprietary information

2-27

Image 28

Contents AT&T Security System Pursuant to Company InstructionsService is all about Exceeding those expectations is what AT&T is all aboutSystem KnowledgcGood Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Chart to help determine what you need. Outline Obtain the floor plan and component list/work orderWhich are part of the AT&T Security Survey Call the customer to verify the time and locationCommon Hand Tools Slotted-Head Screwdriver Phillips-Head ScrewdriverEnvironment WiringRequirements Page Meet the Customer Confirm Correct Location Salesman has told him/herYou can answer any questions before you leave Look for broken windows, scratched paint, torn wallpaperLarge neighborhood antennas Choose Central Controller Location PrecautionsPaper mills Objects MetaI kitchen or bathroom cupboardsRefrigerators MetaI sinks and tubsWireless Remote Transmitter Keypad Transmitter ISI Wireless Siren ControllerAntenna Placement Transmitter locationsAntenna length less than I5 feet, if possible ThemPossible Antenna Run in a Multi-level Home Transformer Signal must pass through several outer walls Wire lath in plaster wallsProblems, especially in L shaped homes InsulationHouse code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Install the Digital Communicator Environmental17Problem. Reset the watchdog with the AT&T Model Possible. Sharp angles in the wiring run reduceProgram the Digital Communicator using the AT&T Remote Programming PackageRun the Central Controller Antenna Choose the antenna run It is critical that you identifySources of possible RF interference Potential blocks to RF wavesPower Up the Central Controller Plug in the Transformer Verify powerEnter the Installer Test Mode Digital displayKeypad Transmitter Choose Transmitter Mounting LocationsAllow at least two inches between the unit and the ceiling Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Wireless Remote/Transmitter Alarm Hour Sensor Loop Not SecureBattery is OK CONDITlONSensor Run the Phone Line for the Digital Communicator Locate the phone line protector blockStep LYll Then install the High Power Siren Requires more powcr than 450 MARelay Module Recheck All Transmitter LocationsBeeps and alarms to specific transmitters. Code numbers Program the TransmittersLet’s look at the I.D. Code for a moment Number is used by the Central Controller to relay trouble1171 Selectable sensor loop zone House code setting Wireless Remote/Transmitter DIP SwitchesProgramming Selectable sensor loop optionSet House Code/Option DIP Switches = closed loop= high security = low securityPage White Wire Yellow Wire Third Number 1st = B 2nd = WPage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Housing Press up on the tab at the bottomIntrusion Audible Panic Interior Auxiliary EnvironmentalAT&T Proprietary Information Lens Replace lens brackets carefully Transmitter PIR TAT&T Proprietary Information PscH8$E Active Post on Pirt Circuit BoardPage Use the information presented in the Installation Open the detector front housingAccessed through a small hole in the backplate Set the House code DIP switches$t.ns~ Switch Page Sensor manufacturer’s instructions Mount the Transmitters Mount Wireless Remote/TransmitterMount the backplate USE Jumpers To Close Loops For Handheld USE Attach the front housing Mount Keypad TransmitterMount Universal Transmitter Page Panic APPLlCATiONS Auxiliary APPLlCATlONSReduce the sensitivity of the Pirt by using Comes on when you moveSeveral minutes to stabilize Walk test the Pirt to verify its coverageExit the Installer Test Mode On = Silent OFF = Sound Switch 9 should Always be on Choose the Wireless Siren /ControllerSources of possible RF interference Potential blocks to RF wavesTransformer Plug in the transformer Verify that the AC Power Light is onScrew provided #6-32 Until 1 Beep is heard System Test Hardwired Perform the System TestSystem Test 24-Hour Zone Transmitters RF Scanner