Graco 313539F important safety instructions Component Identification, Reactor H-VR

Page 10

Component Identification

Component Identification

NOTICE

To prevent damage to soft key buttons, do not press the buttons with sharp objects such as pens, plastic cards, or fingernails.

Reactor H-VR

Key for FIG. 3

BA Component A Pressure Relief Outlet

BBComponent B Pressure Relief Outlet EC Heated Hose Electrical Connector

EM Electric Motor, Fan, and Belt Drive (behind shroud)

FA	Component A Fluid Manifold Inlet (on left side of manifold
	block)
FB	Component B Fluid Manifold Inlet
FH	Fluid Heater (behind shroud)
FM	Reactor Fluid Manifold
FV	Fluid Inlet Valve (B side shown)
GA	Component A Outlet Pressure Gauge
GB	Component B Outlet Pressure Gauge
HA	Component A Hose Connection
HB	Component B Hose Connection
HC	Hydraulic Pressure Control
HP	Hydraulic Pressure Gauge
LR	ISO Lube Pump Reservoir
MC Motor Control Display
MP Main Power Switch
OP	Overpressure Rupture Disk Assembly (on rear of A and B
	pumps)
RS	Red Stop Button
SA	Component A PRESSURE RELIEF/SPRAY Valve
SB	Component B PRESSURE RELIEF/SPRAY Valve
SC	Fluid Temperature Sensor Cable
SN	Serial Number Plate (one inside cabinet, one on right side
	of cabinet)
SR	Electrical Cord Strain Relief
TA	Component A Pressure Transducer (behind gauge GA)
TB	Component B Pressure Transducer (behind gauge GB)
TC	Temperature Control Display
TD	Oil Cooler
VR	Pump Assembly (see page 12)

10

313539F

Image 10

Contents Important Safety Instructions OperationContents ModelsSupplied Manuals Related ManualsElectric Shock Hazard Fire and Explosion Hazard Keep Components a and B Separate Isocyanate ConditionsMaterial Self-ignition Moisture Sensitivity of IsocyanatesChanging Materials Key for FIG Typical Installation, with circulationSide Supply Detail Typical Installation, without circulation Component Identification Reactor H-VRDetail of Reactor Fluid Manifold Shroud removed for clarity Inside cabinetPump Assembly Detail of Pump Assembly guard removed for clarityActual Temperature Key/LED Temperature Controls and IndicatorsMain Power Switch Target Temperature Key/LEDTemperature Displays Temperature Scale Keys/LEDs Circuit BreakersTemperature Arrow Keys Heater Zone On/Off Keys/LEDsPark Key/LED Motor Controls and IndicatorsMotor ON/OFF Key/LED Pressure Key/LEDHydraulic Pressure Control Knob Spray AdjustmentsCycle Count Key/LED Motor Control Arrow KeysLocate Reactor SetupGeneral equipment guidelines Electrical Requirements kW/Full Load Amps Voltage Phase Amps Watts 256886 230V 26,600 256887 400VElectrical requirements See table SystemConnect feed pumps Install Fluid Temperature Sensor FTSConnect pressure relief lines Connect whip hose to gun fluid manifold Connect heated hoseClose gun fluid manifold valves a and B Pressure check hoseGround system Check hydraulic fluid levelStartup Alaf Load fluid with feed pumps Set temperatures Temperature Controls and Indicators, see Manual current control mode only Set pressureChange pressure imbalance setting optional Available Pressure Imbalance SettingsSpraying SprayOpen gun fluid manifold valves a and B Standby ShutdownPressure Relief Procedure Circulation Through Reactor Fluid CirculationPressure RELIEF/CIRCULATION Circulation Through Gun Manifold CKRTemperature Control Diagnostic Codes Diagnostic CodesCode Code Name Alarm Zone Motor Control Diagnostic Codes Code Code Name Alarm orMaintenance Frequency of Oil Changes Ambient Recommended TemperatureFluid Inlet Strainer Screen Fluid Inlet StrainerFlushing RELIEF/CIRCULATIONDimensions Technical Data Category DataFlow Rate in lb/min kg/min Performance ChartsPressure in psi MPa, bar Flow Rate in gal/min liter/minDelta T in degrees F degrees C Flow Rate in gpm lpm313539F Graco Standard Warranty Graco Information