Yamaha RX-SL80 owner manual Impedance Selector switch

Page 12

SPEAKER SETUP

■IMPEDANCE SELECTOR switch

CAUTION

Do not change the setting of the IMPEDANCE SELECTOR switch when the unit power is switched on, as doing so may damage the unit.

If this unit fails to turn on when STANDBY/ON is pressed on either the front panel or remote control, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the way to either position when this unit is in standby mode. Be sure to move this switch only when this unit is in standby mode.

Select the switch position (top or bottom) according to the impedance of the speakers in your system.

MAINS

IMPEDANCE SELECTOR switch

Switch	Speaker	Impedance level
position	Speaker	Impedance level
position

	Front	The impedance of each speaker
Top		The impedance of each speaker
		must be 4	Ω or higher.
	Center, Surround



	Front	The impedance of each speaker
Bottom		The impedance of each speaker
		must be 6	Ω or higher.
	Center, Surround

Image 12

Contents RX-SL80 For U.K. customers Special Instructions for U.K. ModelContents Features Built-in 5-channel original Yamaha digital power amplifierSound field features Other featuresSupplied accessories Installing batteries in the remote controlGetting Started Please check that you received all of the following partsControls and Functions Front panelRemote control AMP mode Infrared windowDSP program / Numeric buttons Operation buttonsUsing the remote control Handling the remote controlEurope models only Front panel display Speaker Setup Speaker placementReturn the tab to secure the wire Speaker connectionsCable tags 10 mm 3/8Impedance Selector switch Impedance Selector switchSpeaker connections Front terminalsSurround terminals Center terminalsSignal directions and cable indications ConnectionsVideo 2 jacks on the front panel Analog jacksConnecting other components Connecting a TVConnecting AV components Digital audio connectionsConnecting the antennas Connecting the AM loop antennaFrequency Step Asia and General Models only Orient the AM loop antenna for the best receptionConnecting the power Turning on the powerConnecting the AC power Front panel Remote controlBasic Setup Using Basic SetupBasic Setup Speaker set upBspeaker Level Press STANDBY/ON to turn on the power Adjust the volume to the desired output levelPlayback Basic operationsTo listen with headphones Silent Cinema To adjust the toneAudio source Remote control Playing video sources BackgroundRemote control operation Front panel operation Press DSP, then rotate VOLUME/SELECT within 5 secondsProgram name Listening to unprocessed input signals StraightNight listening modes Downmixing to 2 channelsTuning Automatic and manual tuningAutomatic tuning LightsManual tuning DisappearsPresetting stations Automatically presetting FM stationsHold down VOLUME/SELECT for more than 5 seconds FM appears in the front panel displaySelecting preset stations Manually presetting stationsRemote control operation Tune into a stationReceiving RDS stations Changing the RDS mode To cancel this functionPress PTY Seek Mode to set this unit in the PTY Seek mode Press u Preset d to select the desired program typeEON function Manual Setup To change the Scart SET settingRecording SET MenuSound Field Program Descriptions For movie/video sourcesRemote button Programs Sound Field For music sources SourcesUsing the sleep timer Advanced OperationsEnjoying multi-channel software Enjoying 2-channel software Listening to high fidelity stereo sound Direct StereoVirtual Cinema DSP Select the input sourceWithin 5 seconds Displaying information about the input Source Using the test tone Press AMP to select the AMP modeRemote control Press TEST/RETURN onUse to quickly setup basic system parameters see Use to manually adjust speaker and system parametersUse to reassign digital input and select the input mode Use to adjust the optional system parametersChanging parameter settings Factory settings. If this happens, edit the parameterPress AMP, then press SET Menu to enter Press / repeatedly to select a menu, then press EnterSound Menu 1/2 Center SPFront SP Surr L/R SP02ASUBWOOFER Phase Subwoofer phase Subwoofer PhaseLFE/BASS OUT Cross OverCSP Distance Dcenter GEQElfe Level Fdynamic Range Gaudio SETInput Menu OpticalBinput Mode Adisplay SETDimmer Dimmer Menu shift Menu ShiftBmemory Guard Dtuner SETDscart SET CPARAM. INIRemote Control Features Control areaControlling this unit Controlling other componentsSetting remote control codes Default codesSetting a code Hold down Code SET while doing steps 2Controlling other components VCRWhat is a sound field Editing Sound Field ParametersElements of a sound field Press / repeatedly to adjust the sound field parameter For 5ch StereoFor PRO Logic II Music CT Width Center widthTroubleshooting GeneralOr DTS indicator Volume levelOther settings on this Unit cannot be Changed No sound fromTuner Remote control Glossary Audio formatsVideo signal information Sound field programsAudio information Specifications Audio SectionVCR DVD NS-P240 NS-P246 NS-P240 Important Safety Instructions FCC Information for US customers Precautions For the SW-P240Table of contents Package contents IntroductionSetting up the speakers Positioning the center speaker NX-C120 Positioning the subwoofer SW-P240Mounting the front and surround speakers To mount the speakers on a wallConnections Basic connection exampleConnecting speaker cables Before connecting the cablesPre-adjusting the subwoofer vol- ume Sounds. Adjust the ampliﬁer’s volume control toIncrease the volume gradually to adjust the vol Adjust the volume of the entire sound systemAdvanced Yamaha Active Servo Technology on the SW-P240 Problem Cause What to Do Power plug is not securely Turn the power switch OFF, thenConnected Connect the power plug securely For the Subwoofer SW-P240 onlyFrequency characteristics Dimensions W x H x DWeight Output PowerAll rights reserved