Yamaha RX-SL80 owner manual Setting remote control codes, Default codes, Setting a code

Page 49

Setting remote control codes

Once you set the appropriate remote control codes, you can use this remote to control your other components. Note that some buttons may not correctly operate the selected component. Use the input selector buttons to select the component you want to operate. The remote control automatically switches to the appropriate control mode for that component.

■Default codes

The following table shows the default component (Library: component category) and the remote control code for each area.

Input area	Manufacturer	Code

TV (DTV/CBL)	YAMAHA	299

VCR	YAMAHA	399

DVD (DVD/CD)	YAMAHA	699

Note

You may not be able to operate your YAMAHA component even if a YAMAHA remote control code is initially set as listed above. In this case, try to set another YAMAHA remote control code.

■Setting a code

1Hold down CODE SET while doing steps 2 and 3.

CODE SET

2Press an input selector button to select the source component you want to set up.

DVD/CD	VCR	VIDEO 1
DTV/CBL	TUNER	VIDEO 2

REMOTE CONTROL FEATURES

3Press the numeric buttons to enter the three- digit remote control code for the component to be used, then release CODE SET.

STEREO HALL JAZZ ROCK

1	2	3	4
MUSIC	ENTERTAIN TV THTR		MOVIE
5	6	7	8

STANDARD NIGHT EXTD SUR. STRAIGHT

9 0 +10 ENT

EFFECT

Refer to “LIST OF REMOTE CONTROL CODES” at the end of this manual.

y

To reset an input area’s remote control code to the factory default, input the default code (see “Default codes” above) in step 3.

Notes

•If the manufacturer of your component has more than one code, try each of them until you find the correct one.

•If you wait for more than 10 seconds during step 3, the setup process is canceled. If this happens, start over from step 2.

•Replace the batteries frequently. The settings may be lost after two minutes without power supply.

•If the remote control code is successfully set, “Code Set OK” appears in the front panel display of this unit. If the setting is not successful, “Code Set NG” appears.

OPERATION	ADVANCED

English

47

Image 49

Contents RX-SL80 Special Instructions for U.K. Model For U.K. customersContents Built-in 5-channel original Yamaha digital power amplifier FeaturesSound field features Other featuresInstalling batteries in the remote control Supplied accessoriesGetting Started Please check that you received all of the following partsFront panel Controls and FunctionsInfrared window Remote control AMP modeDSP program / Numeric buttons Operation buttonsHandling the remote control Using the remote controlEurope models only Front panel display Speaker placement Speaker SetupSpeaker connections Return the tab to secure the wireCable tags 10 mm 3/8Impedance Selector switch Impedance Selector switchFront terminals Speaker connectionsSurround terminals Center terminalsConnections Signal directions and cable indicationsVideo 2 jacks on the front panel Analog jacksConnecting a TV Connecting other componentsConnecting AV components Digital audio connectionsConnecting the AM loop antenna Connecting the antennasFrequency Step Asia and General Models only Orient the AM loop antenna for the best receptionTurning on the power Connecting the powerConnecting the AC power Front panel Remote controlUsing Basic Setup Basic SetupBasic Setup Speaker set upBspeaker Level Adjust the volume to the desired output level Press STANDBY/ON to turn on the powerPlayback Basic operationsTo adjust the tone To listen with headphones Silent CinemaAudio source Remote control Playing video sources BackgroundPress DSP, then rotate VOLUME/SELECT within 5 seconds Remote control operation Front panel operationProgram name Straight Listening to unprocessed input signalsNight listening modes Downmixing to 2 channelsAutomatic and manual tuning TuningAutomatic tuning LightsDisappears Manual tuningAutomatically presetting FM stations Presetting stationsHold down VOLUME/SELECT for more than 5 seconds FM appears in the front panel displayManually presetting stations Selecting preset stationsRemote control operation Tune into a stationReceiving RDS stations To cancel this function Changing the RDS modePress PTY Seek Mode to set this unit in the PTY Seek mode Press u Preset d to select the desired program typeEON function To change the Scart SET setting Manual SetupRecording SET MenuFor movie/video sources Sound Field Program DescriptionsRemote button Programs Sound Field Sources For music sourcesAdvanced Operations Using the sleep timerEnjoying multi-channel software Listening to high fidelity stereo sound Direct Stereo Enjoying 2-channel softwareSelect the input source Virtual Cinema DSPWithin 5 seconds Displaying information about the input Source Press AMP to select the AMP mode Using the test toneRemote control Press TEST/RETURN onUse to manually adjust speaker and system parameters Use to quickly setup basic system parameters seeUse to reassign digital input and select the input mode Use to adjust the optional system parametersFactory settings. If this happens, edit the parameter Changing parameter settingsPress AMP, then press SET Menu to enter Press / repeatedly to select a menu, then press EnterCenter SP Sound Menu 1/2Front SP Surr L/R SPSubwoofer phase Subwoofer Phase 02ASUBWOOFER PhaseLFE/BASS OUT Cross OverDcenter GEQ CSP DistanceElfe Level Gaudio SET Fdynamic RangeInput Menu OpticalAdisplay SET Binput ModeDimmer Dimmer Menu shift Menu ShiftDtuner SET Bmemory GuardDscart SET CPARAM. INIControl area Remote Control FeaturesControlling this unit Controlling other componentsDefault codes Setting remote control codesSetting a code Hold down Code SET while doing steps 2VCR Controlling other componentsEditing Sound Field Parameters What is a sound fieldElements of a sound field For 5ch Stereo Press / repeatedly to adjust the sound field parameterFor PRO Logic II Music CT Width Center widthGeneral TroubleshootingVolume level Or DTS indicatorOther settings on this Unit cannot be Changed No sound fromTuner Remote control Audio formats GlossarySound field programs Video signal informationAudio information Audio Section SpecificationsVCR DVD NS-P240 NS-P246 NS-P240 Important Safety Instructions FCC Information for US customers For the SW-P240 PrecautionsTable of contents Introduction Package contentsSetting up the speakers Positioning the subwoofer SW-P240 Positioning the center speaker NX-C120To mount the speakers on a wall Mounting the front and surround speakersBasic connection example ConnectionsBefore connecting the cables Connecting speaker cablesSounds. Adjust the ampliﬁer’s volume control to Pre-adjusting the subwoofer vol- umeIncrease the volume gradually to adjust the vol Adjust the volume of the entire sound systemAdvanced Yamaha Active Servo Technology on the SW-P240 Power plug is not securely Turn the power switch OFF, then Problem Cause What to DoConnected Connect the power plug securely For the Subwoofer SW-P240 onlyDimensions W x H x D Frequency characteristicsWeight Output PowerAll rights reserved