Yamaha RX-SL80 owner manual Remote control

Page 56

TROUBLESHOOTING

 

The desired station

The signal is weak or the antenna

Tighten the AM loop antenna connections

 

cannot be tuned in with

connections are loose.

and orient it for best reception.

 

 

the automatic tuning

 

 

 

 

 

Use the manual tuning method.

23

 

method.

 

 

 

 

 

 

 

There are continuous

Noises result from lightning,

Use an outdoor antenna and a ground wire.

 

crackling and hissing

fluorescent lamps, motors,

This will help somewhat, but it is difficult to

 

 

noises.

thermostats and other electrical

eliminate all noise.

 

AM

 

equipment.

 

 

 

There are buzzing and

A TV set is being used nearby.

Move this unit away from the TV.

 

whining noises

 

 

 

 

The AM loop antenna is placed near

Place the AM loop antenna away from the

 

(especially in the

 

evening).

the speaker cables.

speaker cables.

 

 

 

The AM ANT and GND cords are

Make sure the white cord is inserted into the

14

 

 

inserted in the wrong terminal.

AM ANT terminal and the black cord into

 

 

 

 

the GND terminal.

 

 

 

 

 

 

Remote control

Problem

Cause

Remedy

Refer to

page

 

 

 

 

 

 

 

The remote control

Wrong distance or angle.

The remote control will function within a maximum

6

does not work or

 

range of 6 m (20 ft) and no more than 30 degrees off-

 

function properly.

 

axis from the front panel.

 

 

 

 

 

 

Direct sunlight or lighting (from an

Reposition this unit.

 

inverter type of fluorescent lamp, etc.) is

 

 

 

striking the remote control sensor of this

 

 

 

unit.

 

 

 

 

 

 

 

The batteries are weak.

Replace all batteries.

3

 

 

 

 

 

The remote control code was not correctly

Set the remote control code correctly.

47

 

set.

 

 

 

Try to set the other codes of the same manufacturer.

47

 

 

 

 

 

 

 

Even if the remote control code is

 

 

 

correctly set, some models may not

 

 

 

respond to the remote control.

 

 

 

 

 

 

54

Image 56
Contents RX-SL80 For U.K. customers Special Instructions for U.K. ModelContents Features Built-in 5-channel original Yamaha digital power amplifierSound field features Other featuresSupplied accessories Installing batteries in the remote controlGetting Started Please check that you received all of the following partsControls and Functions Front panelRemote control AMP mode Infrared windowDSP program / Numeric buttons Operation buttonsEurope models only Using the remote controlHandling the remote control Front panel display Speaker Setup Speaker placementReturn the tab to secure the wire Speaker connectionsCable tags 10 mm 3/8Impedance Selector switch Impedance Selector switchSpeaker connections Front terminalsSurround terminals Center terminalsSignal directions and cable indications ConnectionsVideo 2 jacks on the front panel Analog jacksConnecting other components Connecting a TVConnecting AV components Digital audio connectionsConnecting the antennas Connecting the AM loop antennaFrequency Step Asia and General Models only Orient the AM loop antenna for the best receptionConnecting the power Turning on the powerConnecting the AC power Front panel Remote controlBasic Setup Using Basic SetupBasic Setup Speaker set upBspeaker Level Press STANDBY/ON to turn on the power Adjust the volume to the desired output levelPlayback Basic operationsTo listen with headphones Silent Cinema To adjust the toneAudio source Remote control Playing video sources BackgroundProgram name Remote control operation Front panel operationPress DSP, then rotate VOLUME/SELECT within 5 seconds Listening to unprocessed input signals StraightNight listening modes Downmixing to 2 channelsTuning Automatic and manual tuningAutomatic tuning LightsManual tuning DisappearsPresetting stations Automatically presetting FM stationsHold down VOLUME/SELECT for more than 5 seconds FM appears in the front panel displaySelecting preset stations Manually presetting stationsRemote control operation Tune into a stationReceiving RDS stations Changing the RDS mode To cancel this functionPress PTY Seek Mode to set this unit in the PTY Seek mode Press u Preset d to select the desired program typeEON function Manual Setup To change the Scart SET settingRecording SET MenuRemote button Sound Field Program DescriptionsFor movie/video sources Programs Sound Field For music sources SourcesEnjoying multi-channel software Using the sleep timerAdvanced Operations Enjoying 2-channel software Listening to high fidelity stereo sound Direct StereoWithin 5 seconds Virtual Cinema DSPSelect the input source Displaying information about the input Source Using the test tone Press AMP to select the AMP modeRemote control Press TEST/RETURN onUse to quickly setup basic system parameters see Use to manually adjust speaker and system parametersUse to reassign digital input and select the input mode Use to adjust the optional system parametersChanging parameter settings Factory settings. If this happens, edit the parameterPress AMP, then press SET Menu to enter Press / repeatedly to select a menu, then press EnterSound Menu 1/2 Center SPFront SP Surr L/R SP02ASUBWOOFER Phase Subwoofer phase Subwoofer PhaseLFE/BASS OUT Cross OverElfe Level CSP DistanceDcenter GEQ Fdynamic Range Gaudio SETInput Menu OpticalBinput Mode Adisplay SETDimmer Dimmer Menu shift Menu ShiftBmemory Guard Dtuner SETDscart SET CPARAM. INIRemote Control Features Control areaControlling this unit Controlling other componentsSetting remote control codes Default codesSetting a code Hold down Code SET while doing steps 2Controlling other components VCRElements of a sound field What is a sound fieldEditing Sound Field Parameters Press / repeatedly to adjust the sound field parameter For 5ch StereoFor PRO Logic II Music CT Width Center widthTroubleshooting GeneralOr DTS indicator Volume levelOther settings on this Unit cannot be Changed No sound fromTuner Remote control Glossary Audio formatsAudio information Video signal informationSound field programs Specifications Audio SectionVCR DVD NS-P240 NS-P246 NS-P240 Important Safety Instructions FCC Information for US customers Precautions For the SW-P240Table of contents Package contents IntroductionSetting up the speakers Positioning the center speaker NX-C120 Positioning the subwoofer SW-P240Mounting the front and surround speakers To mount the speakers on a wallConnections Basic connection exampleConnecting speaker cables Before connecting the cablesPre-adjusting the subwoofer vol- ume Sounds. Adjust the amplifier’s volume control toIncrease the volume gradually to adjust the vol Adjust the volume of the entire sound systemAdvanced Yamaha Active Servo Technology on the SW-P240 Problem Cause What to Do Power plug is not securely Turn the power switch OFF, thenConnected Connect the power plug securely For the Subwoofer SW-P240 onlyFrequency characteristics Dimensions W x H x DWeight Output PowerAll rights reserved