Yamaha RX-SL80 owner manual Connecting the antennas, Connecting the AM loop antenna

Page 16

CONNECTIONS

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

AM loop antenna	Indoor FM antenna
(included)	(included)
White	Black
AM ANT GND	FM ANT
TUNER	75Ω UNBAL
TUNER

Ground (GND terminal)

For minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it to the terminals on this unit.

2Lift up the tab and insert the white cord into the AM ANT terminal and the black cord into the GND terminal.

Tab

	AM ANT	GND terminal
	terminal	GND terminal
	terminal

Cable wires

Cable wires

Black

White

3Orient the AM loop antenna for the best reception.

Notes

•The AM loop antenna should be placed away from this unit and all speaker cords.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

■Frequency Step (Asia and General

models only)

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP (using SET MENU) according to the frequency spacing in your area (see page 45).

•North, Central and South America: 100 kHz/10 kHz

•Other areas: 50 kHz/9 kHz

14

Image 16

Contents RX-SL80 For U.K. customers Special Instructions for U.K. ModelContents Features Built-in 5-channel original Yamaha digital power amplifierSound field features Other featuresSupplied accessories Installing batteries in the remote controlGetting Started Please check that you received all of the following partsControls and Functions Front panelRemote control AMP mode Infrared windowDSP program / Numeric buttons Operation buttonsHandling the remote control Using the remote controlEurope models only Front panel display Speaker Setup Speaker placementReturn the tab to secure the wire Speaker connectionsCable tags 10 mm 3/8Impedance Selector switch Impedance Selector switchSpeaker connections Front terminalsSurround terminals Center terminalsSignal directions and cable indications ConnectionsVideo 2 jacks on the front panel Analog jacksConnecting other components Connecting a TVConnecting AV components Digital audio connectionsConnecting the antennas Connecting the AM loop antennaFrequency Step Asia and General Models only Orient the AM loop antenna for the best receptionConnecting the power Turning on the powerConnecting the AC power Front panel Remote controlBasic Setup Using Basic SetupBasic Setup Speaker set upBspeaker Level Press STANDBY/ON to turn on the power Adjust the volume to the desired output levelPlayback Basic operationsTo listen with headphones Silent Cinema To adjust the toneAudio source Remote control Playing video sources BackgroundPress DSP, then rotate VOLUME/SELECT within 5 seconds Remote control operation Front panel operationProgram name Listening to unprocessed input signals StraightNight listening modes Downmixing to 2 channelsTuning Automatic and manual tuningAutomatic tuning LightsManual tuning DisappearsPresetting stations Automatically presetting FM stationsHold down VOLUME/SELECT for more than 5 seconds FM appears in the front panel displaySelecting preset stations Manually presetting stationsRemote control operation Tune into a stationReceiving RDS stations Changing the RDS mode To cancel this functionPress PTY Seek Mode to set this unit in the PTY Seek mode Press u Preset d to select the desired program typeEON function Manual Setup To change the Scart SET settingRecording SET MenuFor movie/video sources Sound Field Program DescriptionsRemote button Programs Sound Field For music sources SourcesAdvanced Operations Using the sleep timerEnjoying multi-channel software Enjoying 2-channel software Listening to high fidelity stereo sound Direct StereoSelect the input source Virtual Cinema DSPWithin 5 seconds Displaying information about the input Source Using the test tone Press AMP to select the AMP modeRemote control Press TEST/RETURN onUse to quickly setup basic system parameters see Use to manually adjust speaker and system parametersUse to reassign digital input and select the input mode Use to adjust the optional system parametersChanging parameter settings Factory settings. If this happens, edit the parameterPress AMP, then press SET Menu to enter Press / repeatedly to select a menu, then press EnterSound Menu 1/2 Center SPFront SP Surr L/R SP02ASUBWOOFER Phase Subwoofer phase Subwoofer PhaseLFE/BASS OUT Cross OverDcenter GEQ CSP DistanceElfe Level Fdynamic Range Gaudio SETInput Menu OpticalBinput Mode Adisplay SETDimmer Dimmer Menu shift Menu ShiftBmemory Guard Dtuner SETDscart SET CPARAM. INIRemote Control Features Control areaControlling this unit Controlling other componentsSetting remote control codes Default codesSetting a code Hold down Code SET while doing steps 2Controlling other components VCREditing Sound Field Parameters What is a sound fieldElements of a sound field Press / repeatedly to adjust the sound field parameter For 5ch StereoFor PRO Logic II Music CT Width Center widthTroubleshooting GeneralOr DTS indicator Volume levelOther settings on this Unit cannot be Changed No sound fromTuner Remote control Glossary Audio formatsSound field programs Video signal informationAudio information Specifications Audio SectionVCR DVD NS-P240 NS-P246 NS-P240 Important Safety Instructions FCC Information for US customers Precautions For the SW-P240Table of contents Package contents IntroductionSetting up the speakers Positioning the center speaker NX-C120 Positioning the subwoofer SW-P240Mounting the front and surround speakers To mount the speakers on a wallConnections Basic connection exampleConnecting speaker cables Before connecting the cablesPre-adjusting the subwoofer vol- ume Sounds. Adjust the ampliﬁer’s volume control toIncrease the volume gradually to adjust the vol Adjust the volume of the entire sound systemAdvanced Yamaha Active Servo Technology on the SW-P240 Problem Cause What to Do Power plug is not securely Turn the power switch OFF, thenConnected Connect the power plug securely For the Subwoofer SW-P240 onlyFrequency characteristics Dimensions W x H x DWeight Output PowerAll rights reserved