Sanyo VCC-MD800P, VCC-MD400P, VCC-MD500, VCC-MD300P, VCC-MD600P, VCC-MD700 Change history

Page 41

Change history

2006.12.20: the issue of ver 1.00

2007.02.15: the issue of ver 1.01

••Changes the DEFAULT communication speed (BAUDRATE) of the MD800 – 500 to 9600 bps.

••Newly added commands.

Cover Offset OFF/ON

Cover Offset Level

Auto Focus Mode during pan/tilt

ATW Mask Display

Center BLC Area Display

BLC Mask Display

Motion Size Display

Motion Mask Display

D/N Filter Slide Time

Status type 7

Status type 8

••Newly added stabilizer function command and function description (only MD700/800 can be used).

••Newly added auto pursuit function command and function description.

••Newly added exclusive processing note.

••Newly added focus lens offset function description.

••Newly added icon of application software and description postscript.

••Revised privacy mask setting note.

••Revised power source, power consumption specifications.

2007.05.10: the issue of ver 1.02

•• Newly added commands.

OSD setting command (MD500 – 800 only) Camera ID setting command

Area Mask Position Full Screen Set (MD 500-800 only) Mask Area Center Position (MD 500-800 only)

••The privacy mask maximum setting value has been increased from 8 to 15. (MD 500-800 only)

••The tilt degree range of the Privacy Masking, Pan/Tilt Degree command has been expanded to: –180 to 180 degrees. The related commands and instructions have been revised. (MD500-800 only)

••Newly added angle area to the specifications of each model.

2007.06.19: the issue of ver. 1.03

•• Newly added commands.

Zoom Direct with Focus (MD500 – 800 only)

•• Change in required time from Wide end Tele end

2007.11.01: the issue of ver.1.04

•• Add new commands below:

Pixel defect compensation command.

Auto pixel defect compensation command at start-up.

••Revise Zoom Direct with Focus command.

••Add exclusive processing table.

••Add method of model distinguishing.

••Add Smart ATW description.

••Add info regarding time-period of accepting the commands after start-up.

••Add notices below:

Pixel defect compensation function

Auto pursuit function

− 40 −

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Technical Manual VVer Contents VCC-MD800/700/600/500 Series Parts Names and DimensionsDimensions VCC-MD400/MD300 Series Parts Names and DimensionsConnection of the Interface Board and Camera Unit Interface Board SpecificationsConnection External Synchronous Signals Input-Output Terminal Layout and SpecificationsInput-Output Terminal Descriptions FFC ComplianceCommunications Format Communications ProtocolDuring Settings Command During Query Command ACKDuring Query Command Other than ACK Communications FlowMWB Command List for MD800-500ATW BLC on BLC OFFELS OFF ELS onAGC ON/OFF AGCOFF SMART1Alarm OUT on Line OUT OFF Alarm Alarm OUT OFFOSD EepromCS FF Command List Query for MD800-500− 13 − − 14 − Command List for MD400 − 16 − − 17 − Burst on Level DAY ColorADJ Direct B Command List Query for MD400Model VCC-MD800/700/600/500/400/300 Example Motion Mask Area Settings Figure⁃⁃ Status Command 3 Only MD400 ⁃⁃ Status Command 2 Except for MD300⁃ ⁃ Status Command 6 Only MD800/700/600/500 ⁃⁃ Status Command 4 Only MD800/700/600/500⁃⁃ Status Command 5 Only MD800/700/600/500 ⁃⁃ When setting Sense UP Auto switch setting⁃⁃ When setting the motion setting to on When unable to set ⁃⁃ When setting V-RESO UP to on When unable to setModel Code Communications Protocol Zoom Control Function DescriptionsZoom Position Control ⁃⁃ Direct ⁃⁃ Tele/WideWhite Balance Control Focus ControlAGC Control Iris ControlShutter Speed Control Backlight Compensation Motion Detection 10 Day/Night Switch ControlAperture Setting the Mask Angle Area Mask Degree Set Privacy Mask Settings Display Area Ntsc PALDetails of the Mask Angle and Position Area Mask Degree SetSetting the Mask Position Area Mask Position Set Frequency that can be stabilized To clarify the image when using the stabilizerStabilizer Auto Pursuit Function Moving Distance Query CommandCommunications Error Camera Control Command TransmissionApplication Software RS-232C PortSpectral Sensitivity Characteristics Ntsc system SpecificationsPAL system Change history Change history
Top Page Image Contents