Sanyo VCC-MD500 Application Software, Camera Control Command Transmission, Communications Error

Page 37

Application Software

[1] Camera Control Command Transmission

1-1 Control using the Command Button

The camera unit can be controlled by clicking the various command buttons.

The command data transmitted and received by the PC can be confirmed using the “SENDING DATA” and “RECEIVING DATA” windows.

Command Button

Operation

Zoom (TELE/WIDE)

Controls the ZOOM function.

 

Press down the button to start the ZOOM function.

 

Release the button to stop the ZOOM function.

Focus (FAR/NEAR)

Controls the FOCUS function.

 

Press down the button to start the FOCUS function.

 

Release the button to stop the FOCUS function.

Focus (Auto/Manual/1PushAF)

Selects the FOCUS function mode.

Shutter Speed (Shutter Speed) (−/OFF/+)

Selects the shutter speed function mode.

 

Click the OFF button to return to initial settings.

Iris (Auto/Manual EI OFF/Manual EI ON)

Selects the iris function mode.

Iris (Level−/Level+)

Selects the iris level.

White Balance (Auto/Manual/1 push/3200K/5600K/FLUO)

Selects the white balance mode.

 

 

White Balance (R−/R+/B−/B+)

Use the color R and B levels to adjust the white balance according to

 

lightening conditions.

BLC (OFF/MULT/CENT/MASK)

Selects the BLC mode.

 

 

AGC (ON/OFF)

Selects the AGC mode. (AGC OFF is invalid when Day/Night is set to

 

AUTO.)

Version

Displays the version of the connected camera.

 

 

1-2 Input Command Data Controls (Refer to the command list)

The camera unit can be controlled by entering the command data into the PC.

Enter a specific protocol in the box within the “SENDING DATA” window (starting from box No.0). The camera is operated by clicking the “Manual Send” button. Similar to Item 1-1 (control using command button), the data received from the camera can be confirmed in the “RECEIVING DATA” window.

In addition, display can be switched between a decimal/hexadecimal number display using “DEC”, “HEX”.

[2] Communications Error

An error message displays when a communications error occurs and communication between the camera and PC stops for several seconds.

Communication can be stopped manually by clicking the “Manual Stop” button.

[3] RS-232C Port

Select the port to connect the RS-232C cable from COM1 to COM4 using the “Port” button

[4] BAUDRATE

Select the communication speed using the “BAUDRATE” button.

[5] ID SET, ID Keyboard

The camera ID can be set in the “ID SET”, “ID Keyboard” tabs.

(Does not apply to MD-300, 400 models)

− 36 −

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Technical Manual VVer Contents Dimensions Parts Names and DimensionsVCC-MD800/700/600/500 Series VCC-MD400/MD300 Series Parts Names and DimensionsConnection Interface Board SpecificationsConnection of the Interface Board and Camera Unit External Synchronous Signals Input-Output Terminal Layout and SpecificationsInput-Output Terminal Descriptions FFC ComplianceCommunications Format Communications ProtocolDuring Settings Command During Query Command ACKDuring Query Command Other than ACK Communications FlowATW Command List for MD800-500MWB BLC on BLC OFFELS OFF ELS onAGC ON/OFF AGCOFF SMART1Alarm OUT on Line OUT OFF Alarm Alarm OUT OFFOSD EepromCS FF Command List Query for MD800-500− 13 − − 14 − Command List for MD400 − 16 − − 17 − Burst on Level DAY ColorADJ Direct B Command List Query for MD400Model VCC-MD800/700/600/500/400/300 Example Motion Mask Area Settings Figure⁃⁃ Status Command 3 Only MD400 ⁃⁃ Status Command 2 Except for MD300⁃⁃ Status Command 5 Only MD800/700/600/500 ⁃⁃ Status Command 4 Only MD800/700/600/500⁃ ⁃ Status Command 6 Only MD800/700/600/500 ⁃⁃ When setting Sense UP Auto switch setting⁃⁃ When setting the motion setting to on When unable to set ⁃⁃ When setting V-RESO UP to on When unable to setModel Code Communications Protocol Zoom Control Function DescriptionsZoom Position Control ⁃⁃ Direct ⁃⁃ Tele/WideWhite Balance Control Focus ControlShutter Speed Control Iris ControlAGC Control Backlight Compensation Aperture 10 Day/Night Switch ControlMotion Detection Setting the Mask Angle Area Mask Degree Set Privacy Mask Settings Display Area Ntsc PALDetails of the Mask Angle and Position Area Mask Degree SetSetting the Mask Position Area Mask Position Set Stabilizer To clarify the image when using the stabilizerFrequency that can be stabilized Auto Pursuit Function Moving Distance Query CommandCommunications Error Camera Control Command TransmissionApplication Software RS-232C PortSpectral Sensitivity Characteristics Ntsc system SpecificationsPAL system Change history Change history
Top Page Image Contents