16 | Sanyo VCC-MD800P, VCC-MD400P, VCC-MD500, VCC-MD300P, VCC-MD700

Communications Protocol

Model: VCC-MD400/300

Message

Backlight

BLC OFF

Backlight compensation OFF

Multi BLC ON

Backlight compensation multifractionated evaluative metering mode (Backlight compensates after

measuring the light of the entire screen.)

Multi BLC Weight -

Sensitivity settings during Multi BLC

Multi BLC Weight +

BLC is easier to determine with a larger value (Initial value: 7)

Multi BLC Weight Preset

Returns sensitivity during Multi BLC to factory defaults (Initial value: 7)

Multi BLC Weight Direct

p: Direct sensitivity settings 0-15 during Multi BLC (Initial value: 7)

Multi BLC Bright -

Brightness settings during Multi BLC

Multi BLC Bright +

Larger value increases brightness when determining BLC (Initial value: 7)

Multi BLC Bright Preset

Returns brightness settings during Multi BLC to factory defaults (Initial value: 7)

Multi BLC Bright Direct

p: Direct brightness settings 0-15 during Multi BLC (Initial value: 7)

Center BLC ON

BLC center-weighted metering mode (Backlight compensates after measuring the light mainly in the

center.)

Center BLC Weight Preset

Returns sensitivity settings during Center BLC to factory defaults (Each initial value: 0)

Center BLC Weight Direct

Sensitivity settings during Center BLC

p: Top(0-7) q: Bottom(0-7) r: Left(0-7) s: Right(0-7) (Each initial value: 0)

Center BLC Area Preset

Returns center area settings during Center BLC to factory defaults (Each initial value: 0)

Center BLC Area Direct

Center area settings during Center BLC

p: x-position(0-7) q: y-position(0-5) r: x-size(0-7)

s: y-size(0-5)

(Initial value: x-position: 2 y-position: 1 x-size: 3 y-size: 3)

*When x-size:0 y-size:0, it becomes 1 area.

Mask BLC ON

BLC mask mode

Mask BLC Area Preset

Return mask area settings during Mask BLC to factory defaults

Mask BLC Area Direct

Mask area settings during Mask BLC

(Note 1)



BLC ON

Returns to the mode before BLC OFF only when BLC OFF

Shutter

Shutter Speed +

Increases shutter speed by one notch

Speed

Shutter Speed -

Decreases shutter speed by one notch

Shutter Speed Set long

Shutter Speed Mode Settings

0: Prolonged exposure shutter mode, 1: Normal mode, 3: High speed shutter mode

Shutter Speed OFF

Same as Shutter Speed Set OFF

Shutter Long Direct

Shutter speed settings during prolonged exposure shutter mode

(0: x1, 1: x2, 2: x4, 3: x8, 4: x16, 5: x32)

Shutter Short Direct

Shutter speed settings during high speed shutter mode

(0: 1/60 (50), 1:1/100 (120), 2: 1/250, 3: 1/500, 4: 1/1000, 5: 1/2000, 6: 1/4000, 7: 1/10000)

Sense Up +

Increase electronic sensitivity settings

Sense Up -

Sense Up Direct

p: Direct increased electronic sensitivity settings

(0: OFF, 1: x2, 2: x4, 3: x8, 4: x16, 5: x32)

ELS OFF

Sets shutter speed to 1x (1/60) after saving

ELS ON

Returns to electronic shutter speed saved by ELS OFF

Motion

Motion Detector OFF

Motion sensor ON/OFF

Detector

Motion Detector ON

Motion Size Preset

Returns detected motion size settings to factory defaults (Initial value: V-Size: 1, H-Size: 1)

Motion Size Direct

Detected motion size settings p: V-Size (1-6) q: H-Size (1-8) (Initial value: V-Size: 1, H-Size: 1)

Alarm Sign OFF

Display ON/OFF during alarm input

Alarm Sign ON

Masking OFF

Mask area settings for motion detection ON/OFF

Masking ON

Mask Area Preset

Returns mask area for motion detection to factory defaults

Mask Area Direct

Mask area settings for motion detection

(Note 1)



Sensitivity Move +

Motion detection sensitivity settings (Initial value: 5)

Sensitivity Move -

Sensitivity Move Preset

Returns motion detection sensitivity settings to factory defaults (Initial value: 5)

Sensitivity Move Direct

p: Direct motion detection sensitivity settings 1-10 (Initial value: 5)

Sensitivity Y-Level +

Minimum brightness settings for motion detection (Initial value: 5)

Sensitivity Y-Level -

Sensitivity Y-Level Peset

Returns minimum brightness settings for motion detection to factory default (Initial value: 5)

Sensitivity Y-Level Direct

p: Direct minimum brightness settings for motion detection 1-10 (Initial value: 5)

Sensitivity Y-Differ +

Brightness variation settings for undetected motion (Initial value: 5)

Sensitivity Y-Differ -

Sensitivity Y-Differ Preset

Returns brightness variation settings for undetected motion to factory defaults (Initial value: 5)

Sensitivity Y-Differ Direct

p: Direct brightness variation settings for undetected motion 1-10 (Initial value: 5)

Sensitivity Duration +

Continuous movement time for motion detection (Initial value: 1)

Sensitivity Duration -

Sensitivity Duration Preset

Returns continuous movement time for motion detection to factory defaults (Initial value: 1)

Sensitivity Duration Direct

p: Direct continuous movement time for motion detection 1-60 (Initial value: 1)

Motion Zoom

p: Zoom magnification during motion detection

(0: OFF, 1: x1.4, 2: x2, 3: x2.8, 4: x4, 5: x6)

Motion Interval

p: Interval time until the start of next detection during motion detection

(0: 5s, 1: 10s, 2: 15s, 3: 20s, 4: 30s, 5: 1m, 6: 2m, 7: 3m, 8: 4m, 9: 5m)

Sync

Sync INT

Internal synchronization mode

Sync L-L

Power supply synchronization mode

L-L Phase +

Synchronous phase settings for power source synchronization

L-L Phase -

L-L Phase Preset

Returns synchronous phase settings for power source synchronization to factory defaults

(Initial value: 0)

L-L Phase Direct

pqr: Synchronous phase settings for power source synchronization

Direct 0-524 (NTSC) / 0-624 (PAL) (Each initial value: 0)

*1: Only MD400

CS: Checksum

*2: Only MD300

FF: Terminator

Sanyo VCC-MD800P, VCC-MD400P, VCC-MD300P, VCC-MD600P, VCC-MD700P, VCC-MD500P 16

Communications Protocol

BLC OFF

BLC ON

ELS OFF

ELS ON

− 16 −