Command List for MD400, Atw | Sanyo VCC-MD400P, VCC-MD500 instruction

Communications Protocol

Model: VCC-MD400/300

[5] Command List for MD400 and 300

Message

System

CAMERA TYPE Unit

CAMERA TYPE Dome

Sanyo Dome Camera ID

CAMERA TYPE Zoom

Sanyo Dome Camera ID

All Initial

Initialization of Unadjusted EEPROM Values (Set to Factory Defaults)

All Menu Initial

Initialization of All Menu Settings

Lens Initial

Detection of initial lens position

Reset

Restarting camera (Saves the setting value)

Menu Initial

Initialization of menu settings other than privacy mask settings

Zoom

Tele

Wide

Tele/Wide Stop

Tele/Wide Speed

p: Speed 1-4 during Tele and Wide commands (1: Slow-4: Fast [Initial value: 3])

Direct

pqr: Direct Position

・MD400, 0: Wide, 1829: 22x (optical), 2069: 352x (digital)

・MD300, 0: Wide, 2248: 22x (optical), 2488: 352x (digital)

Digital Zoom Tele Limiter command needs to be sent before moving to digital zoom field.

Digital Zoom Tele Limiter

p: Maximum digital zoom magnification (0: x0 [Initial value], 1: x2, 2: x4, 3: x8, 4: x16)

V-Reso.UP OFF/ON

p: Increased vertical sensitivity settings during digital zoom OFF/ON (0: OFF, 1: ON)

VIEW ANGLE Set

p: Vignette Reduction Mode Settings (0: OFF, 1: OVER0・1.05x, 2: OVER1・1.06x,

3: OVER 2・1.07x, 4: OVER 3・1.08x, 5: OVER4・1.09x, 6: OVER5・1.10x) (Initial value: 0)

Zoom Preset ON

Moves the zoom position to the optical TELE edge

Zoom Preset OFF

Returns the zoom position to the position before the “Zoom Preset ON” operation

Focus

Auto Focus ON

Manual Focus ON

One Push Trigger

Operates the auto focus operation once

Far

Near

Far/Near Stop

Far/Near Speed

p: Speed 1-4 during Far and Near commands (1: Slow-4: Fast (Initial value: 2))

Direct

pqr: Direct Position (VCC-MD400 0:Far 3524:Near VCC-MD300 0:Far 4008:Near)

Near Limiter

p: Subject distance limit during auto focus and manual focus

(0: 10 cm, 1: 30cm, 2: 50 cm, 3: 1 m [Initial value], 4: 3 m, 5: 5 m)

Auto Focus Sensitivity

p: Auto focus restart sensitivity settings (0: LOW, 1: HI [Initial value], 2: HI+)

High+ automatically restarts every 10 seconds (only TELE side) in addition to restarting the change in

subject

Focus Area

Settings Determining Auto Focus Areas 1-3

1: Entire screen-3: Only center of the screen (Initial value: 2)

White

ATW

Auto White Balance Mode (Same as "0" in WB Mode)

Balance

MWB

Manual White Balance Mode (Same as "1" in WB Mode)

One Push Trigger (AWC Set)

Executes OnePush in AWC Mode

(Note 7)

AWC Reset

Returns to the original mode only after executing the OnePush Trigger command

ATW Smart OFF/ON

Smart ATW (high color saturation compensation) ON/OFF (OFF: 0 [Initial value], ON: 1)

(Note 7)

*This mode is valid when WB mode is set to ATW.

MWB Red +

MWB Red -

MWB Red Preset

Returns MWB red component settings to factory defaults (Initial value: 64)

MWB Red Direct

pq: Direct MWB red components 0-255

MWB Blue +

MWB Blue -

MWB Blue Preset

Returns MWB blue component settings to factory defaults (Initial value: 64)

MWB Blue Direct

pq: Direct MWB blue components 0-255

ATW Masking OFF

Mask settings ON/OFF during ATW

ATW Masking ON

ATW Mask Area Clr

Initialization of mask settings during ATW

ATW Mask Area Set

Mask area settings during ATW

(Note 1)



Iris

Auto IRIS

Manual IRIS (EI OFF)

Manual IRIS (EI ON)

Iris Level +

Iris level operation during auto iris

Iris Level -

Iris Level Preset

Returns iris levels during auto iris to factory defaults (Initial value: 40)

Iris Level Direct

pq: Iris level 0 (Dark) - 100 (Bright) during auto iris (Initial value: 40)

Manual Iris Stop +

Aperture operation during manual iris (Initial value: 17)

Manual Iris Stop -

Manual Iris Stop Preset

Returns aperture during manual iris to factory default (Initial value: 17)

Manual Iris Stop Direct

p: Aperture 1 (Close) - 17 (Open) during manual iris

*1: Only MD400

CS: Checksum

*2: Only MD300

FF: Terminator

− 15 −