Sanyo VCC-WB4000P instruction manual Alarm Settings

Page 34

Alarm Settings

1ALARM REC USE

This function stops any motion that occurs during alarm setting. After the alarm settings have been made, change this setting to “USE” so that alarms can be detected in accordance with the settings.

2EXTERNAL ALARM

Select “NC” (normal close) or “NO” (normal open) to display the external alarm setting menu.

Available settings:

•OFF: No external alarm input is detected.

•NC: Normal close (normally closed, but input is detected when open).

•NO: Normal open (normally open, but input is detected when closed).

3MOTION DETECTOR

When set to “ON”, the MOTION DETECTOR SET screen is displayed. Sensor marks (ú) are used to set the detection area in this setting screen.

4MOTION DETECTOR LEVEL

This sets the sensitivity level for the sensor marks (ú). See p. 38 for details on the sensitivity level.

5ALARM MODE

This selects what combination of external alarm and motion detector is to be used to provide alarm input. Make this setting when “EXTERNAL ALARM” is set to either “NC” or “NO” or “MOTION DETECTOR” is set to “ON”.

The ALARM OUT terminal settings also need to be made.

Available settings:

•AND: An alarm is generated when both the external alarm and the motion sensor receive alarm input.

•OR: An alarm is generated when either the external alarm or the motion sensor receives alarm input.

6ALARM OUT

This is used to make settings for a device such as a buzzer that is connected to the ALARM OUT terminal at the rear of the camera when an alarm is input.

When “NC” (normal close) or “NO” (normal open) is selected, the ALARM OUT MODE or ALARM OUT TIME menu is displayed.

Available settings:

•OFF: No alarm is output when an alarm is received.

•NC: Normal close (normally closed, but an alarm is output when open).

•NO: Normal open (normally open, but an alarm is output when closed).

7ALARM OUT MODE

This operation can be used to manually switch to output to the ALARM OUT terminal regardless of whether an alarm is being received or not. When set to “ON”, the REMOTE ALARM indicator is displayed in the initial screen. (p. 38)

8ALARM OUT TIME

This sets the alarm duration when the external alarm or motion detector detects an alarm, or when the REMOTE ALARM button is pressed when using the remote function.

The “REMOTE” setting only appears when “ALARM OUT MODE” is set to “REMOTE CONTROL”.

Available settings:

2, 5, 10, 15, 20, 30, 60 sec., 2, 3, 4, 5 min., REMOTE

English

– 33 –

Page 33 Page 35
Image 34
Page 33 Page 35
Contents VCC-WB4000P Network CameraContents Precautions FeaturesAccessories Operating environment Name and Function of Each Part Monitor OUT connectorPower indicator Lens mount capName and Function of Each Part Remove the lens mount cap Attach the CS mount-type lens Attaching the LensFor C mount type Flange Back Adjustment Connections Basic ConnectionsConnecting to a LAN ConnectionsWired LAN Settings p Network Camera Wired LAN SettingsInstallation of Plug-in Software to the Computer p Computer Network SET Settings pTurn on the power for the computer Network Camera Wired LAN SettingsInstallation of Plug-in Software to the Computer Click the OK buttonUninstalling the plug-in software Click the Install buttonPlug-in software Cookie Settings Browser SettingsCamera uses cookies Example Subnet mask setting Type Wired LAN SettingsLanguage selection window Initial Camera Screen Image quality mode select buttonsAvailable settings Auto default setting FineAlarm indicator Wireless LAN buttonAlarm button Menu select buttonsRed indicator Lit orange alarm recording image playback is not possibleLit green alarm recording image playback is possible Grey indicatorSET button Resolution and Expansion settings default settings 640x480Selection screen example JImage display areaClick the Network menu select button Network SET SettingsSet the password Network SpeedWhen a password has been changed Changing a passwordMAC Address display Changing the Access Level ID2 or ID3 Turn the camera off and then back on againFor Operator access level Access Level SettingsFor User access level Timezone Clock SET SettingsDaylight Saving Mode Daylight SavingCamera Title Camera SettingsLive Image IrisCamera Settings Setting manual white balance ManualSetting the camera title DAY/NIGHT SettingsMode BurstSet Burst to OFF example Click the SET button Auto Mode SettingsColor Mode Settings Set Polarity to no exampleMode Settings Set AGC Gain to +12 dB example Click the SET buttonConnection example Figure Change the DAY/NIGHT setting to Color modeChange the DAY/NIGHT setting to Timer mode IR lampAlarm Settings Click the Alarm menu select buttonAlarm Settings Alarm Buffering SET Setting Set Alarm Buffering to ON, and then click the Detail button External Alarm Sensor SettingAlarm Resolution Set Alarm REC USE to USE and then click the SET buttonMotion Detector SET Settings Set the sensor marksExternal Alarm Sensor and Motion Detector Settings Alarm Output for a Specified Period Motion Detector Level Sensitivity SettingRemote Alarm Operations Set Motion Detector Level to 2 exampleContinuous Alarm Output Set Buffering Area to PRE/POST 0/10 Pre-alarm/Post-alarm RecordingAlarm detected Set Buffering Area to PRE/POST 2/8Example 1 If Priority is set to Picture Quality Recording New Alarm DataFixed Settings During Pre/Post-Alarm Recording Example 2 If Priority is set to TimeSaving to an Expansion Memory Card Alarm Data indicator green will illuminateInsert the expansion memory card Viewing Live Images Viewing the View Frame Screen Viewing Live ImagesClick the View Frame menu select button Descriptions of Alarm Operation Buttons Playing Back Alarm DataPlaying Back Alarm Data in the Camera’s Internal Memory Frame RateClick the Alarm Data indicator while it is red or green Playing Back Alarm DataPlaying Back Alarm Images Stored in a Computer Playing Back Expansion Memory Card ImagesEND ResolutionPrevious Alarm Data Deleting Saving Alarm Images onto a Computer as Still Images Saving Live Images and Alarm ImagesSaving Live Images onto a Computer When the File Download pop-up menu is displayed, click Save Saving Live Images and Alarm ImagesSaving All of a Single Alarm Event onto a Computer Click the Play button and then click the Download buttonWireless LAN device settings TCP/IP settings Wireless LAN SET SettingsCamera wired LAN settings TCP/IP settings Camera wireless LAN settings TCP/IP settingsWireless LAN SET Settings Camera Wireless LAN SettingsDescription of Wireless LAN SET Screen Encipherment SettingsConnecting the camera and installing the software PPP Dial-up SettingsPPP Connection to an Internet Service Provider Double-click the Camset icon on the desktopClick the Save Info File button PPP Dial-up SettingsClick the SET to Camera button Close the Camset windowAuthentication Dial to Provider SettingsProvider TEL. no Camera Computer Dial from PC SettingPPP Connection from a Computer Telephone lineMake the settings in the PPP setting screen Set the following itemsClick the RS-232C menu select button RS-232C Settings RS-232C SETLanguage Selection Click the Language button to change the languageFirmware Version Status CheckingClick the Status menu select button SUB-MICROCOMPUTER VersionGlossary of Terms Glossary of Terms Pre-alarm and post-alarm recording If the camera cannot be connected TroubleshootingIf you forget the IP Address Specifications Dimensions Specifications136 mm 126 mm 12 mm 85 mm 59 mm 51 mm Printed on recycled paper 1AC6P1P2682 L5AM2/XE 0603KP-CZ
Top Page Image Contents