Sanyo VCC-WB4000P instruction manual External Alarm Sensor Setting, Alarm Resolution, Overwrite

Page 36

Alarm Settings

5ALARM RESOLUTION

This sets the image size for data being recorded into the internal memory.

Note: When playing back images that have been recorded at a size of 720x240, the vertical size will be adjusted so that they become 720x480 images.

6OVERWRITE

Always be sure to insert the expansion memory card into the card slot before turning on the power for the camera. If you insert the card after the power has been turned on, this item will not be displayed.

If this is set to “ON”, old alarm images are automatically deleted when the internal memory becomes full, and the new data is written over as it is captured.

External Alarm Sensor Setting

1 Connect a device such as an infrared sensor to the ALARM IN terminal at the rear of the camera.

2 Set “ALARM REC USE” to “NO USE” (example).

2 3

3 Set “EXTERNAL ALARM” to “NO” (example).

For example, if a door is closed, it will trigger an alarm.

For details, see “2 EXTERNAL ALARM”.

4 Set “ALARM OUT” to “NO” (example).

For example, you can cause a buzzer that is connected to the ALARM OUT terminal to sound.

For details, see “6 ALARM OUT”.

4

5 6

5 Set “ALARM OUT MODE” to “ALARM OUT”.

6 Use the drop-down list box to change the “ALARM OUT TIME” setting to “60 sec.” (example).

7 Set “ALARM SOUND MODE” to “USE”.

7 9

8

8 Set “RECORD SIZE” to “CC”.

If “CC” is selected, recording will only be carried out while an alarm is being input. If “FULL” is selected, recording will continue from the point where an alarm starts to be input until the recording area is full. The recording area is the capacity that has been set in “BUFFERING AREA”.

9 Set “ALARM BUFFERING” to “ON”, and then click the [DETAIL] button.

The ALARM BUFFERING SET screen will be displayed.

10 Change any settings that are required for recording alarm images into the internal memory, and then click the [SET] button.

For example, you can set the following.

The alarm images (16MB) will be recorded at high quality at a resolution of 720x240.

11 Set “ALARM REC USE” to “USE” and then click the [SET] button.

When an alarm is detected, the alarm will sound and the ALARM DATA indicator in the initial screen will be displayed.

English

– 35 –

Image 36
Contents VCC-WB4000P Network CameraContents Precautions FeaturesAccessories Operating environment Monitor OUT connector Power indicatorName and Function of Each Part Lens mount capName and Function of Each Part Attaching the Lens Remove the lens mount cap Attach the CS mount-type lensFor C mount type Flange Back Adjustment Connections Basic ConnectionsConnecting to a LAN ConnectionsNetwork Camera Wired LAN Settings Installation of Plug-in Software to the Computer pWired LAN Settings p Computer Network SET Settings pNetwork Camera Wired LAN Settings Installation of Plug-in Software to the ComputerTurn on the power for the computer Click the OK buttonClick the Install button Uninstalling the plug-in softwarePlug-in software Browser Settings Cookie SettingsCamera uses cookies Wired LAN Settings Example Subnet mask setting TypeLanguage selection window Image quality mode select buttons Available settings Auto default settingInitial Camera Screen FineWireless LAN button Alarm buttonAlarm indicator Menu select buttonsLit orange alarm recording image playback is not possible Lit green alarm recording image playback is possibleRed indicator Grey indicatorResolution and Expansion settings default settings 640x480 Selection screen exampleSET button JImage display areaNetwork SET Settings Set the passwordClick the Network menu select button Network SpeedChanging a password When a password has been changedMAC Address display Changing the Access Level ID2 or ID3 Turn the camera off and then back on againAccess Level Settings For Operator access levelFor User access level Clock SET Settings Daylight Saving ModeTimezone Daylight SavingCamera Settings Live ImageCamera Title IrisCamera Settings Setting manual white balance ManualSetting the camera title DAY/NIGHT SettingsMode BurstAuto Mode Settings Color Mode SettingsSet Burst to OFF example Click the SET button Set Polarity to no exampleMode Settings Set AGC Gain to +12 dB example Click the SET buttonChange the DAY/NIGHT setting to Color mode Change the DAY/NIGHT setting to Timer modeConnection example Figure IR lampAlarm Settings Click the Alarm menu select buttonAlarm Settings Alarm Buffering SET Setting External Alarm Sensor Setting Alarm ResolutionSet Alarm Buffering to ON, and then click the Detail button Set Alarm REC USE to USE and then click the SET buttonMotion Detector SET Settings Set the sensor marksExternal Alarm Sensor and Motion Detector Settings Motion Detector Level Sensitivity Setting Remote Alarm OperationsAlarm Output for a Specified Period Set Motion Detector Level to 2 exampleContinuous Alarm Output Pre-alarm/Post-alarm Recording Alarm detectedSet Buffering Area to PRE/POST 0/10 Set Buffering Area to PRE/POST 2/8Recording New Alarm Data Fixed Settings During Pre/Post-Alarm RecordingExample 1 If Priority is set to Picture Quality Example 2 If Priority is set to TimeAlarm Data indicator green will illuminate Saving to an Expansion Memory CardInsert the expansion memory card Viewing Live Images Viewing Live Images Viewing the View Frame ScreenClick the View Frame menu select button Playing Back Alarm Data Playing Back Alarm Data in the Camera’s Internal MemoryDescriptions of Alarm Operation Buttons Frame RatePlaying Back Alarm Data Playing Back Alarm Images Stored in a ComputerClick the Alarm Data indicator while it is red or green Playing Back Expansion Memory Card ImagesResolution ENDPrevious Alarm Data Deleting Saving Live Images and Alarm Images Saving Alarm Images onto a Computer as Still ImagesSaving Live Images onto a Computer Saving Live Images and Alarm Images Saving All of a Single Alarm Event onto a ComputerWhen the File Download pop-up menu is displayed, click Save Click the Play button and then click the Download buttonWireless LAN SET Settings Camera wired LAN settings TCP/IP settingsWireless LAN device settings TCP/IP settings Camera wireless LAN settings TCP/IP settingsWireless LAN SET Settings Camera Wireless LAN SettingsDescription of Wireless LAN SET Screen Encipherment SettingsPPP Dial-up Settings PPP Connection to an Internet Service ProviderConnecting the camera and installing the software Double-click the Camset icon on the desktopPPP Dial-up Settings Click the SET to Camera buttonClick the Save Info File button Close the Camset windowDial to Provider Settings AuthenticationProvider TEL. no Dial from PC Setting PPP Connection from a ComputerCamera Computer Telephone lineMake the settings in the PPP setting screen Set the following itemsRS-232C Settings RS-232C SET Language SelectionClick the RS-232C menu select button Click the Language button to change the languageStatus Checking Click the Status menu select buttonFirmware Version SUB-MICROCOMPUTER VersionGlossary of Terms Glossary of Terms Pre-alarm and post-alarm recording Troubleshooting If the camera cannot be connectedIf you forget the IP Address Specifications Specifications Dimensions136 mm 126 mm 12 mm 85 mm 59 mm 51 mm Printed on recycled paper 1AC6P1P2682 L5AM2/XE 0603KP-CZ