Sanyo VCC-WB4000P PPP Connection from a Computer, Dial from PC Setting, Camera Computer

Page 58
Modem commands consist of a single line starting with the letters "AT", followed by the commands as shown below. Generally you should issue an "AT&K4" command to switch to software flow control, but this may vary depending on the product. Refer to the specifications for the modem being used for further details on this.
MODEM: INITIALIZECOMMAND AT&K4

PPP (Dial-up) Settings

9 Make the following settings if required.

BAUD RATE: Normally “115200 bps

DATA SIZE: Normally “8 bits

PARITY: Normally “NONE

STOP BIT: Normally “1

10 Once you have finished changing the settings, click the [SET] button.

MODEM CONNECTIONS

The modem should be an RS-232C external modem that is compatible with the command set devised by Hayes Corporation of the United States.

Large volumes of data may be transmitted depending on the alarm settings, so a high-speed modem using a protocol such as V.90 should be used.

Note: The maximum receiving speed for the V.90 protocol is 56 Kbps, but the transmission speed is 33.6 Kbps. Because of this, the maximum transmission speed for alarm data from a camera or the video server will be

33.6Kbps, even for modems that use the

V.90 protocol.

The cameras and video server can only use software (Xon/Xoff) flow control. In may cases, the modems may be set up to use hardware (RTS/CTS) flow control. In such cases, you will need to use AT command settings to change the modem settings to

software flow control.

PPP Connection from a Computer

You can use the Dial-up networking function of a computer to connect the computer to the camera via a telephone line. This method does not involve an Internet Service Provider.

Camera

Computer

Modem

Telephone line

Modem

DIAL FROM PC Setting

1 Click the [PPP] menu select button.

The PPP SET screen will be displayed.

2 Select “USE” from the “DIAL FROM PC” drop-down list box and then click the [DETAIL] button.

The PPP SET (FROM PC) screen will be displayed.

English

– 57 –

Image 58
Contents VCC-WB4000P Network CameraContents Precautions FeaturesAccessories Operating environment Name and Function of Each Part Monitor OUT connectorPower indicator Lens mount capName and Function of Each Part Remove the lens mount cap Attach the CS mount-type lens Attaching the LensFor C mount type Flange Back Adjustment Connections Basic ConnectionsConnecting to a LAN ConnectionsWired LAN Settings p Network Camera Wired LAN SettingsInstallation of Plug-in Software to the Computer p Computer Network SET Settings pTurn on the power for the computer Network Camera Wired LAN SettingsInstallation of Plug-in Software to the Computer Click the OK buttonUninstalling the plug-in software Click the Install buttonPlug-in software Cookie Settings Browser SettingsCamera uses cookies Example Subnet mask setting Type Wired LAN SettingsLanguage selection window Initial Camera Screen Image quality mode select buttonsAvailable settings Auto default setting FineAlarm indicator Wireless LAN buttonAlarm button Menu select buttonsRed indicator Lit orange alarm recording image playback is not possibleLit green alarm recording image playback is possible Grey indicatorSET button Resolution and Expansion settings default settings 640x480Selection screen example JImage display areaClick the Network menu select button Network SET SettingsSet the password Network SpeedWhen a password has been changed Changing a passwordMAC Address display Changing the Access Level ID2 or ID3 Turn the camera off and then back on againFor Operator access level Access Level SettingsFor User access level Timezone Clock SET SettingsDaylight Saving Mode Daylight SavingCamera Title Camera SettingsLive Image IrisCamera Settings Setting manual white balance ManualSetting the camera title DAY/NIGHT SettingsMode BurstSet Burst to OFF example Click the SET button Auto Mode SettingsColor Mode Settings Set Polarity to no exampleMode Settings Set AGC Gain to +12 dB example Click the SET buttonConnection example Figure Change the DAY/NIGHT setting to Color modeChange the DAY/NIGHT setting to Timer mode IR lampAlarm Settings Click the Alarm menu select buttonAlarm Settings Alarm Buffering SET Setting Set Alarm Buffering to ON, and then click the Detail button External Alarm Sensor SettingAlarm Resolution Set Alarm REC USE to USE and then click the SET buttonMotion Detector SET Settings Set the sensor marksExternal Alarm Sensor and Motion Detector Settings Alarm Output for a Specified Period Motion Detector Level Sensitivity SettingRemote Alarm Operations Set Motion Detector Level to 2 exampleContinuous Alarm Output Set Buffering Area to PRE/POST 0/10 Pre-alarm/Post-alarm RecordingAlarm detected Set Buffering Area to PRE/POST 2/8Example 1 If Priority is set to Picture Quality Recording New Alarm DataFixed Settings During Pre/Post-Alarm Recording Example 2 If Priority is set to TimeSaving to an Expansion Memory Card Alarm Data indicator green will illuminateInsert the expansion memory card Viewing Live Images Viewing the View Frame Screen Viewing Live ImagesClick the View Frame menu select button Descriptions of Alarm Operation Buttons Playing Back Alarm DataPlaying Back Alarm Data in the Camera’s Internal Memory Frame RateClick the Alarm Data indicator while it is red or green Playing Back Alarm DataPlaying Back Alarm Images Stored in a Computer Playing Back Expansion Memory Card ImagesEND ResolutionPrevious Alarm Data Deleting Saving Alarm Images onto a Computer as Still Images Saving Live Images and Alarm ImagesSaving Live Images onto a Computer When the File Download pop-up menu is displayed, click Save Saving Live Images and Alarm ImagesSaving All of a Single Alarm Event onto a Computer Click the Play button and then click the Download buttonWireless LAN device settings TCP/IP settings Wireless LAN SET SettingsCamera wired LAN settings TCP/IP settings Camera wireless LAN settings TCP/IP settingsWireless LAN SET Settings Camera Wireless LAN SettingsDescription of Wireless LAN SET Screen Encipherment SettingsConnecting the camera and installing the software PPP Dial-up SettingsPPP Connection to an Internet Service Provider Double-click the Camset icon on the desktopClick the Save Info File button PPP Dial-up SettingsClick the SET to Camera button Close the Camset windowAuthentication Dial to Provider SettingsProvider TEL. no Camera Computer Dial from PC SettingPPP Connection from a Computer Telephone lineMake the settings in the PPP setting screen Set the following itemsClick the RS-232C menu select button RS-232C Settings RS-232C SETLanguage Selection Click the Language button to change the languageFirmware Version Status CheckingClick the Status menu select button SUB-MICROCOMPUTER VersionGlossary of Terms Glossary of Terms Pre-alarm and post-alarm recording If the camera cannot be connected TroubleshootingIf you forget the IP Address Specifications Dimensions Specifications136 mm 126 mm 12 mm 85 mm 59 mm 51 mm Printed on recycled paper 1AC6P1P2682 L5AM2/XE 0603KP-CZ