Sanyo VCC-WB4000P instruction manual Flange Back Adjustment

Page 9

Flange Back Adjustment

The flange back is the distance between the lens (sold separately) and the image capturing surface of the camera. It is adjusted at the time of shipment from the factory to accommodate the types of lenses that are generally assumed to be in use.

Accordingly, the flange back does not normally need to be adjusted. However, if attaching a zoom lens and changing from wide angle to telephoto, the images may not be captured in proper focus, and so in such cases the flange back should always be adjusted by following the procedure given below.

1 Connect a coaxial cable between the

TV monitor

 

 

 

 

camera output connector (MONITOR OUT)

 

 

 

 

(sold separately)

 

 

 

 

of the camera and the monitor’s video

 

 

PC CARD

 

 

 

 

 

 

connector (VIDEO IN).

 

MONITOR

ETHERNET

RS-232C

 

 

OUT

 

 

 

 

2 Turn on the camera’s power.

 

 

D/N IN COM AC24V

GND

 

PC

 

 

 

POWER

 

 

 

MODEM1 2

 

 

 

Adjust the flange back while viewing the

 

ALARM IN OUT DC12V

 

 

 

 

 

 

 

camera images on the monitor.

 

 

Power supply

3 Use a Phillips screwdriver to loosen the

 

 

 

 

connector

 

 

 

 

 

flange back locking screws.

 

 

 

 

4

Move the zoom lens to the telephoto

3, 6

 

 

 

 

 

 

 

 

setting, and then use the lens focus ring

 

 

 

 

5

to adjust the focus.

Flange back

 

 

 

Move the zoom lens to the wide angle

locking screw

 

 

 

 

 

 

 

 

setting, and then use the flange back

4

 

 

 

 

adjustment dial to adjust the focus.

 

 

 

 

 

 

 

 

6 Move the zoom lens from wide angle to

 

 

Flange back

 

telephoto (repeating steps 4 and 5) and

 

 

 

check that the images are properly

 

5

locking screw

 

focused. Then tighten the flange back

 

 

 

 

 

 

 

 

locking screws.

– 8 –

English

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Network Camera VCC-WB4000PContents Precautions FeaturesAccessories Operating environment Power indicator Monitor OUT connectorName and Function of Each Part Lens mount capName and Function of Each Part Attaching the Lens Remove the lens mount cap Attach the CS mount-type lensFor C mount type Flange Back Adjustment Basic Connections ConnectionsConnections Connecting to a LANInstallation of Plug-in Software to the Computer p Network Camera Wired LAN SettingsWired LAN Settings p Computer Network SET Settings pInstallation of Plug-in Software to the Computer Network Camera Wired LAN SettingsTurn on the power for the computer Click the OK buttonClick the Install button Uninstalling the plug-in softwarePlug-in software Browser Settings Cookie SettingsCamera uses cookies Wired LAN Settings Example Subnet mask setting TypeLanguage selection window Available settings Auto default setting Image quality mode select buttonsInitial Camera Screen FineAlarm button Wireless LAN buttonAlarm indicator Menu select buttonsLit green alarm recording image playback is possible Lit orange alarm recording image playback is not possibleRed indicator Grey indicatorSelection screen example Resolution and Expansion settings default settings 640x480SET button JImage display areaSet the password Network SET SettingsClick the Network menu select button Network SpeedChanging a password When a password has been changedMAC Address display Turn the camera off and then back on again Changing the Access Level ID2 or ID3Access Level Settings For Operator access levelFor User access level Daylight Saving Mode Clock SET SettingsTimezone Daylight SavingLive Image Camera SettingsCamera Title IrisSetting manual white balance Manual Camera SettingsDAY/NIGHT Settings Setting the camera titleBurst ModeColor Mode Settings Auto Mode SettingsSet Burst to OFF example Click the SET button Set Polarity to no exampleSet AGC Gain to +12 dB example Click the SET button Mode SettingsChange the DAY/NIGHT setting to Timer mode Change the DAY/NIGHT setting to Color modeConnection example Figure IR lampClick the Alarm menu select button Alarm SettingsAlarm Settings Alarm Buffering SET Setting Alarm Resolution External Alarm Sensor SettingSet Alarm Buffering to ON, and then click the Detail button Set Alarm REC USE to USE and then click the SET buttonSet the sensor marks Motion Detector SET SettingsExternal Alarm Sensor and Motion Detector Settings Remote Alarm Operations Motion Detector Level Sensitivity SettingAlarm Output for a Specified Period Set Motion Detector Level to 2 exampleContinuous Alarm Output Alarm detected Pre-alarm/Post-alarm RecordingSet Buffering Area to PRE/POST 0/10 Set Buffering Area to PRE/POST 2/8Fixed Settings During Pre/Post-Alarm Recording Recording New Alarm DataExample 1 If Priority is set to Picture Quality Example 2 If Priority is set to TimeAlarm Data indicator green will illuminate Saving to an Expansion Memory CardInsert the expansion memory card Viewing Live Images Viewing Live Images Viewing the View Frame ScreenClick the View Frame menu select button Playing Back Alarm Data in the Camera’s Internal Memory Playing Back Alarm DataDescriptions of Alarm Operation Buttons Frame RatePlaying Back Alarm Images Stored in a Computer Playing Back Alarm DataClick the Alarm Data indicator while it is red or green Playing Back Expansion Memory Card ImagesResolution ENDPrevious Alarm Data Deleting Saving Live Images and Alarm Images Saving Alarm Images onto a Computer as Still ImagesSaving Live Images onto a Computer Saving All of a Single Alarm Event onto a Computer Saving Live Images and Alarm ImagesWhen the File Download pop-up menu is displayed, click Save Click the Play button and then click the Download buttonCamera wired LAN settings TCP/IP settings Wireless LAN SET SettingsWireless LAN device settings TCP/IP settings Camera wireless LAN settings TCP/IP settingsCamera Wireless LAN Settings Wireless LAN SET SettingsEncipherment Settings Description of Wireless LAN SET ScreenPPP Connection to an Internet Service Provider PPP Dial-up SettingsConnecting the camera and installing the software Double-click the Camset icon on the desktopClick the SET to Camera button PPP Dial-up SettingsClick the Save Info File button Close the Camset windowDial to Provider Settings AuthenticationProvider TEL. no PPP Connection from a Computer Dial from PC SettingCamera Computer Telephone lineSet the following items Make the settings in the PPP setting screenLanguage Selection RS-232C Settings RS-232C SETClick the RS-232C menu select button Click the Language button to change the languageClick the Status menu select button Status CheckingFirmware Version SUB-MICROCOMPUTER VersionGlossary of Terms Glossary of Terms Pre-alarm and post-alarm recording Troubleshooting If the camera cannot be connectedIf you forget the IP Address Specifications Specifications Dimensions136 mm 126 mm 12 mm 85 mm 59 mm 51 mm Printed on recycled paper 1AC6P1P2682 L5AM2/XE 0603KP-CZ
Top Page Image Contents