Seagate ST3146807FC manual Relative humidity, Effective altitude sea level, Shock and vibration

Page 36

26

Cheetah 10K.6 FC Product Manual, Rev. B

b.Non-operating

–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive.

HDA Temp.

Check Point

Figure 13. Location of the HDA Temperature check point

6.3.2Relative humidity

The values below assume that no condensation on the drive occurs.

a.Operating

5% to 95% non-condensing relative humidity with a maximum gradient of 10% per hour.

b.Non-operating

5% to 95% non-condensing relative humidity.

6.3.3Effective altitude (sea level)

a.Operating

–1,000 to +10,000 feet (–305 to +3,048 meters)

b.Non-operating

–1,000 to +40,000 feet (–305 to +12,210 meters)

6.3.4Shock and vibration

Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is installed in an enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur internally to the enclosure resulting in drive movement in excess of the stated limits. If this situation is apparent, it may be necessary to modify the enclosure to minimize drive movement.

The limits of shock and vibration defined within this document are specified with the drive mounted by any of the four methods shown in Figure 14, and in accordance with the restrictions of Section 8.5. Orientation of the side nearest the LED may be up or down.

6.3.4.1Shock

a.Operating—normal

The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding 15 Gs at a maximum duration of 11 msec (half sinewave). The drive, as installed for normal oper- ation, shall operate error free while subjected to intermittent shock not exceeding 15 Gs at a maximum duration of 2 msec (half sinewave). Shock may be applied in the X, Y, or Z axis.

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Page Page Page Page Revision status summary sheet Revision Date Writer/Engineer Sheets AffectedPage Contents Defect and error management InstallationSeagate Technology support services Interface requirementsList of Figures Cheetah 10K.6 FC Product Manual, Rev. B ViiPage Scope Cheetah 10K.6 FC family disc driveCheetah 10K.6 FC Product Manual, Rev. B Applicable standards and reference documentation Australian C-Tick Korean MICTaiwanese Bsmi Reference documentsGeneral description Cheetah 10K.6 FC disc driveStandard features Media descriptionPerformance ReliabilityFactory-installed accessories Factory-installed optionsUser-installed accessories Unformatted and formatted capacitiesCheetah 10K.6 FC Product Manual, Rev. B Performance characteristics Internal drive characteristicsSeek performance characteristics Access time Format command execution time in minutesGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Reliability specifications Reliability and service Preventive maintenanceService life Service philosophy7 S.M.A.R.T Controlling S.M.A.R.TPerformance impact Milliseconds Reporting controlDetermining rate Predictive failuresState of the drive prior to testing ImplementationInvoking DST Short and extended testsProduct warranty Log page entriesAbort ShippingPhysical/electrical specifications AC power requirementsDC power requirements General DC power requirement notesPower sequencing Conducted noise immunityCurrent profiles +5V +12VTypical ST373307FC drive +12V current profile Typical ST3146807FC drive +5V current profile Typical ST373307FC drive +5V current profile Power dissipation ST3146807FC ST373307FCTemperature Cheetah 10K.6 FC Product Manual, Rev. B ST336607FCRelative humidity Effective altitude sea levelShock and vibration ShockPackage size Packaged/product weight Drop height Recommended mounting Air cleanliness Cheetah 10K.6 FC Product Manual, Rev. B VibrationAcoustics Mechanical specifications Mounting configuration dimensionsDefect and error management Drive internal defects/errorsDrive error recovery procedures Read retry Maximum recovery time per Write retry FC-AL system errorsRead and write retry count maximum recovery times Maximum recovery time perInstallation Drive ID/option selectionLED connections 1 J6 connector requirements Drive FrontDrive orientation CoolingDrive mounting Air flowGrounding FC-AL features Fibre Channel link service framesInterface requirements Fibre Channel task management functionsFibre Channel port login NPort login Plogi payload BytesFibre Channel Process Login Fibre Channel Process Login AcceptNPort Login Accept ACC payload Bytes Process Login Plri payloadFibre Channel fabric login Fabric Login Flogi payload BytesFabric Login Accept ACC payload Bytes Accept or NPort Login when sending frames to an initiatorFibre Channel Arbitrated Loop options Dual port supportFC-AL options supported Option SupportedSupported commands Command code Command name Supported commands Command code Supported Command nameRead descriptor mode Cheetah 10K.6 FC Product Manual, Rev. B Mode Sense data Cheetah 10K.6 FC Product Manual, Rev. B Inquiry dataCheetah 10K.6 FC inquiry data Bytes Data hexCheetah 10K.6 FC Product Manual, Rev. B DEF DEF CHG Cheetah 10K.6 FC Product Manual, Rev. B Miscellaneous operating features and conditions Miscellaneous featuresSupported Feature or condition Miscellaneous statusPhysical characteristics Physical descriptionConnector requirements Part description Positions Part number FeaturesPin Signal name Signal type Pin descriptionsFC-SCA pin descriptions Power Fault LED OutFC-AL transmitters and receivers Active LED OutEnable port bypass signals Motor start controls11 SEL6 through SEL0 ID lines Parallel Enclosure Services Interface ESI Setting Setting Hex DecArbitrated loop physical address Alpa values Signal characteristics TTL input characteristicsLED driver signals Device control codesTransmit eye diagram Differential Pecl inputEye diagram data values Link rate GHzSeagate Technology support services Online Services Automated ServicesPresales Support Technical SupportCustomer Service CSO USA/Canada/Latin America Support ServicesEuropean Support Services Africa/Middle East Support Services Asia/Pacific Support ServicesCall Center Toll-free Direct dial Cheetah 10K.6 FC Product Manual, Rev. B Index FC-AL Cheetah 10K.6 FC Product Manual, Rev. B Plogi Cheetah 10K.6 FC Product Manual, Rev. B Cheetah 10K.6 FC Product Manual, Rev. B
Related manuals
Manual 2 pages 5.2 Kb

ST336607FC, ST373307FC, ST3146807FC specifications

The Seagate ST373307FC, ST3146807FC, and ST336607FC are robust hard disk drives designed for enterprise environments where reliability and performance are critical. Each model offers distinct features suited to various data storage needs, reflecting Seagate's commitment to innovation in storage technology.

The ST373307FC is a 73GB Fibre Channel hard drive that operates at 15,000 RPM, making it exceptionally fast for read and write operations. This drive employs a 4GB cache, enhancing its performance by allowing quicker access to frequently used data. With a 3.5-inch form factor, the ST373307FC is built for high-density environments, delivering reliable access to data. Its Fibre Channel interface supports high-speed connections, essential for data-intensive applications like databases and virtualization.

Next in line, the ST3146807FC offers a capacity of 146GB, also operating at 15,000 RPM. This drive features an 8GB cache, which significantly improves its data transfer rates, making it ideal for transactional workloads. The ST3146807FC is engineered to minimize latency and maximize throughput, ensuring that enterprises can access critical data swiftly and efficiently. Additionally, its rugged construction is designed to withstand the demands of continuous operation, providing peace of mind for businesses with strict uptime requirements.

Lastly, the ST336607FC has a substantial storage capacity of 300GB and shares the 15,000 RPM operational speed that characterizes this high-performance line. With a similar 8GB cache as the ST3146807FC, it offers excellent performance for read-intensive and write-heavy applications. The ST336607FC is also designed with enhanced thermal management features, supporting cooler operations in densely packed server environments. This model is particularly suited for applications such as data warehousing and online transaction processing, where speed and reliability are paramount.

Each of these drives utilizes advanced technologies like Native Command Queuing (NCQ), which optimizes the order of read and write requests. These features, combined with Seagate's reputation for durability and performance, make the ST373307FC, ST3146807FC, and ST336607FC excellent choices for enterprise applications requiring high-speed data access and exceptional reliability. In environments where data integrity and uptime are critical, these drives provide the robust performance necessary to meet demanding storage needs.
Top Page Image Contents